Your cart is empty.
Your cart is empty.Product Description
Tezoro specializes in Home improvement Tools , and we offer innovative products to our customers. Tezoro’s products have been spread all over the world such as North America, Europe, Asia, Oceania.
Tezoro Professional Coping Foot
Why do we recommend Tezoro Professional Coping Foot?
- Improve You work Efficiency-Release your hands
- Tough Steel Construction-Made of plated steel
- Installation and removal takes only a couple of minutes.
- Fit for Most Jigsaw:Except for Porter-Cable, and the Bosch 1590 and 1591
Premium and Durable
The structure is stable and the dense protective film is formed to make the Coping foot rust resistant.
Selected Raw Material
Tezoro Coping Foot are engineered from impact and chemical resistant plated steel,which are very durable and reusable.
The screws above are easy to tighten.
Note：The included screws are suitable for most jigsaws.
If it is not suitable, you need to find the right screw
Outstandingly Helper in coping crown.
Cutting MDF or finger jointed pine is faster and more precise than a coping saw.Our Coping Foot Make coping super easy.
The Coping Foot for freehanding with the jigsaw fits the following tools:
AEG Bosch 1581 1582 1584 1587 470 365 260 572 120 12 volt
DOES NOT FIT 1590, 1591
DeWalt 318 321 323 331
Festool 300 and model previous to the 300
Milwaukee 6268 6266 6256 M12 M18
Makita4341 4351 barrel 4350 handlecordless
Eric Bolz
Reviewed in the United States on September 16, 2024
I could not get it to fit my Dewalt DCS334 but is seems well made. The threaded bolt it came with does not fit the threads on my saw, and the Dewalt bolt was a bit too long and it also would not fit through the slot on the device. So it was a waste of money for me.
Jahamas
Reviewed in the United States on August 6, 2024
came with no instructions, but with my Makita jig i just took the original foot off and used the same screw as what my saw had before
Lo
Reviewed in the United States on December 6, 2024
Very good quality and fits my tool perfectly. This tool makes the job easier and it is reasonably priced.
DH.
Reviewed in the United States on April 14, 2024
It’s a universal fit so it took a couple of minutes to figure out how to install it. It makes coping easy.
FlaMike
Reviewed in the United States on November 19, 2022
I've had the Original Collins Coping Foot on my top handle Bosch Jig Saw. And it did a great job for many. many yrs. Purchased a new barrel Bosch Jig saw and found the coping foot would not interchange. Purchased this one and it seems pretty much the same exact foot. Now this setup has a slight learning curve. Keep the saw speed down, use an aggressive tooth blade and go slow. Used this for baseboard and especially for crown. Try to hold crown at the angle it will be installed so you can back cope it for clearance. It works !
William L.
Reviewed in the United States on March 31, 2021
I purchased this coping foot because it was less expensive than the Collins coping foot. I just received it today. Its packed in a clear bag with Collins instructions and Collins Tool Company stamped in the metal. This is listed as being made by Tezoro so I don't know if its an original Collins part (over run or rebranded) or a knock off with their name on it. It appears to be decent quality and has all the mounting hardware/shims with it. while I have not used it yet, I don't see any reason it shouldn't fit and work like the original Collins foot that it appears to be.
Mr. Mark S. Accardi
Reviewed in the United States on August 20, 2020
works just as expected, fit my Ryobi jigsaw perfectly, If I was installing crown for a living, I would definitely buy a barrel style jigsaw but since I am just doing a small personal project, it worked fine for me. My only disappointment is with amazon and their slow "prime" shipping!!! I pay a premium annually for 2 DAY SHIPPING and get VERRY FEW ITEMS delivered in 2 days lately. Amazon needs to start crediting back membership fees for their inability to deliver on time!!!
Piro
Reviewed in the United States on December 19, 2020
Easy to use once you have setup the work piece correctly. It gave me the confidence to cope the miter cut. After a while I was surprised at how close to the miter cut I could get. I finished off the cope with metal files. But you have to set the work piece up correctly to do this. Initially I had the work piece on a metal sawhorse set on a cement floor. It made the whole piece vibrate when I was doing the cope cut. Then I put a piece of 2x4 on the floor and a cinderblock standing straight up on that. I hung a rope from the top of the horse and tied around the top opening of the block. Then I removed the 2x4 at the bottom. Now I had a heavy weight that prevented the vibrations from shaking the work piece.
Recommended Products
$39.95
$ 18 .99 $18.99
$158.95
$ 75 .99 $75.99