Shopping Cart

Your cart is empty.

Your cart is empty.

Crescent 1/4' Drive Torx Bit Socket T-30 - CDTS5N

Free shipping on orders over $29.99

$2.49

$ 0 .99 $0.99

In Stock

About this item

  • Chrome vanadium alloy steel for long lasting durability
  • Nickel chrome plated for long lasting protection. ASME specifications B107.5
  • Use with ratchet to improve speed in tightening Torx drive fasteners
  • Tools meet stringent new ANSI and ASME specifications and come with a full Satisfaction guarantee
  • Works great on flash, hard-to-grip nails


Trusted by the trades. Since 1907, Crescent has offered quality tools with proven innovation that enables professionals and DIYers alike to get the job done. All sockets and ratchets meet or exceed a.N.S.I load specifications, resulting in tools you can count on to be strong, well-designed, and durable enough to get the job done right, time after time.


frisgee
Reviewed in the United States on August 21, 2024
I had to remove the bed from my Ford Ranger to replace my fuel pump. This little tool,with the help of a piece of pipe over the ratchet handle, made short work of the six bolts holding it down. I sprayed PB blaster on and let it soak in for a day, hit them with a hammer and then they cranked right out. Highly recommended! Great value as I almost bought an impact wrench that would have been way more expensive.
scotty dogg
Reviewed in the United States on July 9, 2024
The tool truck version of these are around 30 bucks each. I can buy a handful of these for the same price and who cares if they break. But they hold up pretty well for the price.
Ricky
Reviewed in the United States on June 23, 2024
Work great
Customer
Reviewed in the United States on October 1, 2024
Happy to get this at a fair price
Sleepflyer
Reviewed in the United States on January 25, 2024
You'll need this to replace a broken door handle on some cars. I used it to work on a 2008 Pontiac Vibe rear driver side handle. It worked like a charm. Feels sturdy and fit on my socket wrench like a glove. Success!
Presidential Customer
Reviewed in the United States on January 10, 2024
I bought this torx 1/4" drive for clutch cover removal or a specific trail emergency. It is in a trail recovery tool bag which I hope I will never use. I made sure it fit the torx bolt well. It looks and feels fine. I'm sure if it is used properly it will work fine for my life.
rheannonskye
Reviewed in Canada on December 29, 2023
Need it for the roof, super easy tool
Philip Butcher
Reviewed in Australia on November 22, 2022
Great product and price
Maggie
Reviewed in Canada on May 26, 2021
The t50 broke on first use with a wrench.I must be very strong or this is junk.
woodstock
Reviewed in the United States on April 27, 2021
OK this is both a good and bad tool depending on expectations/use. I bought this to remove the bed on my 1997 ford ranger. There are 6 T-55 bolts holding the bed on. As this is a one time only job I did want to buy an expensive 1/2 inch impact bit. As I had been soaking the bolts in kroil oil for days I decided to try this low cost bit. Bit arrived within two days(prime). Is chrome like finish not impact, but I knew that. I used a 3/8 to 1/2 inch adapter to my impact wrench. Bolts came out. HAPPY CAMPER!. SO as I already stated tool worked as I expected, good. BUT bit also showed signs of strain(very slight stretching around actual bit to socket joint), not good if I expected to use this bit again/heavy use. This is just fine for light applications only!! I believe would have snapped if not for the kroil. In closing a fine light tool or a one time heavy use on a wing and a prayer. Proper tool for the job and all that!! OH I still have the bit might come in handy someday, and I still have lots of kroil oil.
el chief
Reviewed in Mexico on September 24, 2020
Excelente
Matthew P.
Reviewed in the United States on December 17, 2019
I've had a "Silver Eagle" brand set of Torx bits for a long time, bought off a Matco truck around 14 years ago. I had to warranty a couple of these recently, but since there's no Matco dealer where I'm currently doing business, I had to mail them in for warranty. Took a few weeks, but I did eventually get my replacements from Matco, but they were now Matco-branded, not Silver Eagle. And my T30 was now a fat 3/8" drive and not the 1/4" I had come to rely on in some of the tight spaces I use them frequently in.So, on to search for a replacement. I actually had just a Snap on bit I hammered into a 1/4" socket (also 1/4" drive). That bit has finer tips and started to twist within the first couple times I used it.So, I came here to find something similar to my old Silver Eagle set and found this. Ordered it and after a couple weeks of use I've been very happy. This is very comparable to my old Silver Eagle T30 1/4" drive. The tips are thicker than the Snap On one and so far has held up very well to my use. It almost looks as though it's made by the same company that made the Silver Eagle set 14 years ago. Not sure if it's true, but the size and quality is definitely there.
Brandon D.
Reviewed in Canada on October 27, 2019
strong very sturdy! never eats nuts! very good quality!
Recommended Products