Your cart is empty.
Your cart is empty. Specification:
Thickness: 1.5 inch / 38mm
Vehicle bolt pattern: 5x4.75 / 5x120.65
Wheel bolt pattern: 5x4.75 / 5x120.65
Thread size: M12x1.5
Center bore: 2.78 inch / 70.5mm
Compatible vehicles:
1982-2003 Camaro
1984-2019 Corvette (Does not work on 2020 -2022 vehicles)
1983-2005 Blazer
1982-2004 S10 (Does not work with 2WD Front Hubs)
1995-2002 Jimmy
1990-2004 Sonoma
1982-1990 S15 (Does not work with 2WD Front Hubs)
2004-2009 Cadillac-XLR
1979-1985 Eldorado
* If you don't make sure whether this item fits to you, message us with your vehicle year, make, & model and we will find the item you need. *
Before place an order, you need to know:
- Vehicle fitment compatibility is only a guide, please ensure that these are the correct ones for your vehicle.
- For some special vehicles, the stock lug studs are longer than the adapter or the lug studs of the adapter are shorter to hold the wheel, please contact with us at the first time to return or replace the adapter.
- Returns are accepted, all returns must be made within 20 days of purchase date. Items must be in new, unused condition, with all original materials included with the shipment.
* Important: We strongly recommend please don't install the bolt nuts by electronic tool, it is best by manual wrench.*
Peter
Reviewed in the United States on August 16, 2024
i had first bought one set of two for my rear wheels on a 2002 chevy blazer 2 door , 2 wheel drive . they fit the back great but before i installed them i was changing out the spiked lugs all around so i tried them on the front and they fit perfectly so i bought another set of two for the front . whoever said they do not work on the front of a 02' blazer is wrong. very good buy
Customer
Reviewed in the United States on May 30, 2024
These hubcentric spacers have 1 problem. They do not fit the hub without removing some material. I made the hub was clean, no debris. No surface rust, I used sand paper. After that, the spacers still do not fit over the hub. I had to remove quite a bit of material from inside the spacer for them to fit. Even at that, I still had to push them onto the hub firmly and there was still a large space there. So to pull the spacer flush I had to put the lug nuts on and tighten them down to pull to spacer flat to the surface. I would NOT buy these again.
Customer
Reviewed in the United States on February 3, 2024
Studs snapped off on spacer wrecked my rim thankfully i was only doing 30mph when this happened.
Tim wilkinson
Reviewed in the United States on December 16, 2024
These worked very well on the car thank you so much
Calvin
Reviewed in the United States on August 18, 2022
i have 2019 corvette grand sport this part not fit my car, 19 inc and 20 inc orjinal rims.
Shop-a-holic
Reviewed in the United States on July 13, 2022
The media could not be loaded.
Joe in FL
Reviewed in the United States on February 16, 2022
I bought these hub-centric spacers to install wheels with a greater offset on my 1996 Corvette. These were the cheapest on Amazon. Sometimes with inexpensive products manufacturing quality is sacrificed; specifically when casting metals, there tends to be slight imperfections. There were no imperfections anywhere on these spacers and the powder-coating was flawless. I’d highly recommend these spacers.
Kris
Reviewed in the United States on November 19, 2021
So 1st thing is that these spacers fell and look very well made..and worked perfect..after modifications..on my 91 camaro RS...so these review is basicly points towards 3rd gen camaro/firebird owners...you will have to either file or shave down the outide lip portion of the face of the spacer a good amount to get them to fit the front hub of your camaro/firebird....so what i did was i took a diamond carbide bit on an angle grinder..and went in circles all the way around the lip of the face of the spacer for about 20 min on both fronts...and also shaved the front hubs with a very gritty sandpaper disc..and with the combination of the 2...they fit...very tight..but they fit...and as far as the back?..(drum brakes on mine)..91 camaro RS...just a very minimal amount of cleaning up/sanding the lip of the axle face...not very much..to gwt the rears to fit...and after that they went on jus fine..and my wheels fit perfect....and vioala!.Good to go...so qith some patience and knowledge of basic tools and stuff..it can be done...
Recommended Products
