Your cart is empty.
Your cart is empty.This back glass washer nozzle matches the fit, function and appearance of the original equipment washer nozzle to restore this feature's functionality. Made of durable materials for reliable service. This part is compatible with the following vehicles. Before purchasing, enter your vehicle trim in the garage tool to confirm fitment. [Honda CR-V: 2007, 2008]
Robert M.
Reviewed in the United States on July 24, 2024
Bought it to replace the broken rear window sprayer on my older Honda CRV. Perfect fit. Just be careful and go slow when threading it onto the connection. Both parts are plastic and can be easily damaged if you cross-thread them.
Robert
Reviewed in the United States on February 28, 2024
My original washer spray nozzle broke while I was giving my car a car wash, Amazon recommended another brand that definitely did NOT fit. My buddy managed to find this brand nozzle and it was exactly the one needed for the replacement, made with good quality material and the rubber boot that supplies the washer fluid goes right around the back nut for a good fit.
Naoya O.
Reviewed in the United States on February 27, 2024
If you have the tools, you can replace it in about 10 minutes. I was careful not to break the glass by tightening the screws too hard. It is a little difficult to remove the interior on a cold day. The plastic is hard when it is cold.Finally, the direction of the jet nozzle is adjusted with a needle to complete the process.
Brenda
Reviewed in the United States on February 19, 2024
Don’t know why there are bad reviews on this product. It fit perfect and was an easy job. I have never had a bad Dorman product and this is no exception.
Customer
Reviewed in Canada on May 23, 2023
The item is unusable as either the nut is too big or the threaded part is too big, the nut could not be screw down, very disappointed.
Ali S.
Reviewed in Canada on July 3, 2022
It fitted with my Honda Crv perfectly
Debbie
Reviewed in Canada on June 30, 2022
Works Good!
Weekend Do It Yourselfer.
Reviewed in Canada on November 3, 2022
When assembling the nut started to "cross-thread" however, if to take your time and slowly screw the nut onto the nozzle it will thread correctly, I sprayed a bit of silicone on threads to helped ease the nut onto the nozzle.Once assembled it works like a charm.
KA P.
Reviewed in the United States on November 25, 2022
I got it to work for my 2007 CRV but had to force the nut onto the nozzle and cross thread the nozzle piece . If I had to do it again I probably shell out the extra 8 bucks for the Honda oem replacement.
Avg. Joe
Reviewed in the United States on August 15, 2021
Threaded on fine in less than 10 minutes. You don't have to disassemble the while back panel. Just the little top piece directly behind the middle stop light. Pull the middle then the sides pop out. There is a hole in the glass where you screw it in. Try threading it by hand FIRST then finish snug tight with a 13 mm socket. It is plastic but a metal nut so DO NOT OVER TIGHTEN. No need for silicone or locktight as it's plastic. Took 10 minutes start to finish. Had my wife hold the outside end while I threaded it on by hand ...that's all don't over think it. Good value.
Medic563
Reviewed in the United States on July 13, 2021
Installed in less than 5 minutes on my daughter's 2007 Honda CR-V. No issues at all. Probably not the exact size as the original. The original was knocked off in the car wash so I couldn't compare them, but the marking on the rear glass was a bit larger. As for the reviews that say they cross threaded the new one. I put a little silicone on the threads and hand tightened it as much as I could, then used a socket. No problems with the threads at all. Maybe they didn't make sure they threaded it correctly before using a wrench. I have decades of experience as a mechanic, so it wasn't an issue for me. Total job with R&I of the trim panel was about 10 minutes.
Campin' Cowpoke
Reviewed in the United States on November 17, 2020
As others mentioned, impossible to install without cross threading, even trying it with both parts in hand right in front of my face the thing just won’t go on straight. After accepting the fact that installing it would destroy the threads, I found about the only way it was going to work is if my wife sat inside with the ratchet to tighten it while I held the outside as gently as possible with pliers. Unfortunately because you’re destroying the threads it takes a lot of force to hold it in place while the person inside tightens. Then, once I got it hooked back up to the washer supply line, I activated it only to see that like others, it won’t spray on the glass. Fail all around. I have no idea what the Honda oem part costs, but it’s worth the money over this useless and frustrating hunk of plastic.
D. R.
Reviewed in Canada on October 11, 2020
Good quality and is coming with a valveYou can change the angle for the jet. I used to spray my car backup camera, during the winter gets dirty.
Recommended Products
