Your cart is empty.
Your cart is empty.This direct replacement drum brake wheel cylinder was specifically engineered to match the fit, function and performance of the original wheel cylinder on particular vehicles. It is manufactured and tested for quality assurance. This part is compatible with the following vehicles. Before purchasing, enter your vehicle trim in the garage tool to confirm fitment. [Ford F1: 1948, 1949, 1950, 1951, 1952] - [Ford F-100: 1953, 1954, 1955, 1956, 1957, 1958, 1959, 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967] - [Ford F100: 1965] - [Ford F-250: 1966, 1967, 1968, 1969] - [Ford F350: 1968, 1969, 1970, 1971] - [Ford F-350: 1968, 1969, 1970, 1971] - [Ford Fairlane: 1962, 1963, 1964, 1965] - [Hudson Hornet: 1954] - [Hudson Pacemaker: 1952] - [Hudson Wasp: 1952, 1953] - [International 1100C: 1968] - [Jeep J-2500: 1972, 1973] - [Jeep J-2600: 1972, 1973] - [Mercury Meteor: 1962, 1963] - [Studebaker 3E1: 1958] - [Studebaker 3E10: 1958] - [Studebaker 3E11: 1958] - [Studebaker 3E11D: 1958] - [Studebaker 3E12: 1958] - [Studebaker 3E12D: 1958] - [Studebaker 3E13: 1958] - [Studebaker 3E14: 1958] - [Studebaker 3E16: 1957, 1958] - [Studebaker 3E17: 1957, 1958, 1959] - [Studebaker 4E1: 1959] - [Studebaker 4E11: 1959] - [Studebaker 4E11D: 1959] - [Studebaker 4E12: 1959] - [Studebaker 4E12D: 1959] - [Studebaker 4E13: 1959] - [Studebaker 4E14: 1959] - [Studebaker 4E16: 1959] - [Studebaker Transtar: 1957, 1958]
M and J Gordon
Reviewed in the United States on June 19, 2024
The bole hole openings where off a little or maybe it was not ground out enough. Summit Racing sold me the same part so I can see why there are issues out there.
Phillip Gossman
Reviewed in the United States on May 7, 2024
Installed 2 after jacking up truck pulling wheels removing old slave cyl installing brake drum found out it was machined WRONG DORMAN HAS GONE CHEAP CHINESE
awfulyhairy
Reviewed in the United States on August 28, 2023
Works great on my 1954 Ford F100 truck!
John Holmes
Reviewed in the United States on February 25, 2023
Very happy with the replacement parts for my 1959 Ford F100 restoration project.
Richard
Reviewed in the United States on August 3, 2022
Perfect fit
Bruce lada
Reviewed in the United States on April 22, 2021
Good product and fits
Land of Ice and Snow
Reviewed in Canada on August 3, 2020
Leaks right out of the box! Bolt holes do not align with backing plate. Bleeder screws suck in air must use Teflon tape to stop it. Spend the extra money!
Jonathan
Reviewed in the United States on May 24, 2020
Pros:This wheel cylinder can fit the twin I-beam suspension of old ford with some grinding of the cylinder and the backing plate. This fitment is tough due to the kingpins. If you can get the seal right the first time, these cylinders work great and have been reliable for me in other applications.Cons:The copper washer used to seal the brake fitting is lame. It leaked on me many times, I had to really crank the hose on there to get it to seal. I would recommend fitting your hose on there while the cylinder is in a vice, off of the car. Make sure you test for leaks and check your reservoir often during the first few drives. The strange thing is that other cylinders similar to this from dorman use a flare fitting. I wish they had implemented this!
Sam Plaster
Reviewed in the United States on September 21, 2019
Works great.
Recommended Products
$10.14
$ 4 .99 $4.99