Shopping Cart

Your cart is empty.

Your cart is empty.

DPTOOL 31pcs Wheel Bearing Press Kit Universal Front Wheel Drive Bearing Remover and Installer Kit

Free shipping on orders over $29.99

$85.00

$ 35 .99 $35.99

In Stock
  • Must Have Tool for Wheel Bearing Repair: This wheel bearing kit allows you to quickly and easily remove and install your wheel bearings while keeping the steering knuckle and strut assembled on the vehicle, without hammering and front-end alignment
  • Wide compatibility: This wheel bearing puller press kit contains a wide range of sleeve and bushing sizes that are compatible with most front-wheel drive vehicles on front-wheel drive cars and small pickups
  • Durable and Sturdy: Made of high quality steel with multiple forging and heat treatment, it is very hard, extremely durable and not easily damaged, meanwhile, the tools of different sizes have been professionally tested and can be perfectly matched to the car models, making it a professional tool for removing and installing wheel bearings
  • Easy to use: Precise bushings, sleeves and sliding screws, when assembled, hold your bearings securely, allowing you to pop them out smoothly and without damage, leaving the steering knuckle and strut assembly untouched
  • Package Include: This is a complete set containing sleeve, bushing, washer, wheel hub installer, sleeve plate, sliding forcing screw, sliding forcing nut.



Product Description

31pcs Wheel Bearing Press Kit

Universal Front Wheel Drive Bearing Remover and Installer Kit

  • Function: This wheel bearing kit allows you to quickly and easily remove and install your wheel bearings on front wheel drive vehicles
  • Application: This wheel bearing puller press kit contains a wide range of sleeve and bushing sizes that are compatible with most front-wheel drive vehicles on front-wheel drive cars and small pickups
Front Wheel Drive Bearing Remover and Installer Kit

31pcs Wheel Bearing Press Kit Include:

  • Bushing Outer Diameter: 3.46", 3.28", 3.02", 3.05", 2.94", 2.88", 2.87", 2.81", 2.76", 2.62", 2.49", 2.32", 2.16", 1.96"
  • Socket Outer Diameter: 2.99", 3.26", 3.62", 4.01"
  • Socket Plates Outer Diameter: 3.38", 4"
  • Shaft 22.2 mm x 300 mm with thrust bearing
  • 3 Pin Remove Replace Bolts M12 x 1.5
  • 3 Pin Remove Replace Bolts M14 x 1.5
  • 2x O Rings Seal

Front Wheel Drive Bearing Remover Installer Kit

Multiple Universal Sizes

  • This is a complete front wheel drive bearing remover and installer kit containing sleeve, bushing, washer and so on. It can keep the steering knuckle and strut assembly on the vehicle, eliminating the need for hammering and front-end alignment

Wheel Bearing Press Kit

Durable

  • Made of high quality steel with multiple forging and heat treatment, it is very hard, extremely durable and not easily damaged

Wheel Bearing Press Kit

Professional Craftsmanship

  • The tools of different sizes have been professionally tested and can be perfectly matched to the car models, making it a professional tool for removing and installing wheel bearings

Usage Steps

Universal Front Wheel Drive Bearing Remover and Installer Kit

  • Step 1. Determine if the vehicle has a seized rotor or a floating rotor.
  • Step 2. Assemble the tool assembly and press out the worn bearing.
  • Step 3. Lightly lubricate the new bearing and position it for installation with the assembled tool assembly. Press the bearing into the spindle assembly up to the bottom of the bearing.
  • Step 4. Secure the bearing retainer in place using the bearing retainer bolts.
  • Step 5. Assemble the tool assembly. Lightly oil the hub assembly and install the hub. NOTE: When assembling the bearing installer, the flat side must face the bearing and the small diameter guide must be on the side away from the bearing.
  • Step 6. Assemble the remaining vehicle components removed during replacement of bearings: (1) Lower ball joint and steering knuckle assembly brake rotor. (2) Disc brake caliper. (3) Outer tie rod nut and tie rod. (4) Axle nut. (5) Front tires.

Cristal G.
Reviewed in the United States on March 5, 2025
Bad quality. Very bad
AW2222
Reviewed in the United States on March 14, 2025
This DPTOOL bearing press set arrived in complete shambles. All of the tools had moved around during shipping because it was not very well packed inside and outside of the box. The worst part was the bolts that are used to actually do the pressing were banged together and damaged the threads. Even the blow molded case had damage.At a whopping $85 you would be far better served getting a free rental from the store you bought your bearings from and saving your hard earned money. I can only go 2/5 stars for these reasons as this is a really utilitarian kit that is not a good value proposition.
Luke
Reviewed in the United States on March 10, 2025
This is an excellent kit to have when you do not have access to hydraulic press. There are a ton of adapters that come with a kit to fit almost every bearing you might encounter. My one fear is how well it will stand up over time. If something is extremely seized, you still need to take the proper measures to ensure it comes out or you will damage the kit. When used properly it can be a great tool and save you a lot of time.
E. Smith
Reviewed in the United States on March 10, 2025
I got this to try to se how strong it actually is. It's very strong and high quality. Not what I expected. It easily removed and installed bearings. It comes in a nice case, and the value of product is well within its price. It will last a long time from what I can tell. Great overall product.
W. Arce
Reviewed in the United States on February 23, 2025
This DPTOOL 31pcs Wheel Bearing Press Kit is a must-have for any serious DIY mechanic. This universal kit makes front wheel bearing removal and installation a breeze. The variety of adapters ensures compatibility with most front-wheel-drive vehicles. Sturdy construction and a well-organized case make this a professional-grade tool at a reasonable price.
Eric
Reviewed in the United States on February 19, 2025
We've already got two sets of bearing drivers sets in the shop (one for cars and trucks and one for bigger heavy equipment bearings) but this is a nice compromise of the two sets as it runs up to being able to handle 4" bearing races. This also isn't the only DPTools set we have in the shop and while our other sets are all nicely machined, this set's finish isn't as quite high, but the drivers are completely serviceable for their intended purpose (and is much better than using a 75mm socket to drive a bearing race into a housing).That said, the threaded bits all thread easily with no burrs or need to run a tap or die through them to finish what the factory should have done. So this set will live next to the hydraulic press waiting to get "pressed" into service.
Holly Mattice
Reviewed in the United States on March 4, 2024
good quality