Your cart is empty.
Your cart is empty.The DT Swiss End Caps allow conversion of existing DT Swiss hubs between different wheel spacing standards, or can serve as a replacement for missing or lost end caps. Specific compatibility is described below for the various options in the drop-down menu. The 12 x 100mm option is compatible with 240S CenterLock "fifteen" front hubs, 240S CenterLock straight-pull front hubs, model-year 2014 15 x 100mm white 180 front hubs, and 2016 RC Spline black hubs. The 15 x 100mm option is compatible with model-year 2011 and newer 240 CenterLock disc hubs with 18mm outer diameter axle. It does work for 15 x 110mm Boost, as well. The 12 x 142/148/157mm Shimano/SRAM option works with DT Swiss 180, 240, and 440 mountain hubs with 12 x 142mm, 12 x 148mm, and 12 x 157mm hub spacing. The same end caps are used for all three hub spacings and Shimano HyperGlide freehubs. They do NOT convert non-Boost hubs to Boost spacing. The 12 x 135mm option works with model-year 2011 and newer 240, 350, and 440 hubs. It converts these hubs from standard Quick-Release to 12 x 135mm thru-axle. This option also serves to convert 150mm Quick-Release hubs to 12 x 150mm thru-axle. The 12 x 142mm Road option works with DT Swiss 180, 240, and 350 Road hubs with 11-speed freehub bodies/cassettes. They are compatible with classic flanged hubs only, not straight-pull hubs. The SRAM XD option fits DT Swiss hubs with 12 x 142mm, 12 x 148mm, 12 x 177mm, and 12 x 197mm hub spacing, as all these axle spacings use the same end caps. It only works with SRAM XD freehub drivers.
john june
Reviewed in the United States on March 18, 2024
Helps to have the right parts.
A Gunn
Reviewed in the United States on August 25, 2023
Yes, these end caps do the job that the description says they will do. There are so many end caps and variations out there, its important to do your research to make sure you are getting the right part, and this one is as advertised!
fuel98rider
Reviewed in the United States on April 10, 2021
Perfect endcap replacements for DT Swiss 240S hubs. I bought a new gravel frame, and needed to swap out the QR caps for TA ones. If you have 240S hubs, this is what you need to change over to 12 x 140 n the rear. Swapping the caps out is easy. On the drive side, you need to remove the cassette to pull the caps off. On the rotor side, you will need to remove the rotors. After getting those removed, I put the old caps in an axle vise and popped them off in a snap. It doesn’t take much to break the o-ring seal when removing them. Clean the hubs off and slide the new ones on, and push them in until don’t go in any further. The long endcap is on the rotor side, the short one is on the drive side.
Kalinga
Reviewed in the United States on December 5, 2020
Accurate description and perfect product
Daniel Galvez Lopez
Reviewed in the United States on November 8, 2019
The description of the product isn't clear and I got confused and I understood that this caps will change from 142 to 148 the width of the hub.
Mark
Reviewed in the United States on January 17, 2018
The smaller of the two caps will be needed for a DT SWISS 350 hub, for converting to a SRAM 1-12 drive train. To remove the old one, pull with a pair of players remove the hub, clean and replace with a XD Driver from 365 bikes. The 3 "PAUL" Ratcheting will not work. Grease with Phil Wood grease (not to much). Reassemble. Need more help. See YouTube videos on this or ask me. Torque to 35 foot pounds.
Recommended Products
$385.00
$ 99 .00 $99.00