Your cart is empty.
Your cart is empty.Product Description
Adjustable Braided Line
The braided part can be shorten to meet your need by cutting.
Specifications
- Total Length: 12inch/30.5cm
- Diameter: 1/8" NPT gauge port (gauge not included, available separately)
- Weight: 0.7lbs/350g
- Fitting Material: Lightweight Aluminum
- Hose Material: Stainless Steel Braided
Please allow 0.5-1 inch difference due to manual measurement.
The braided part can be shorten to meet your need by cutting.
Notice: If the hose ends leaked, it is recommended to use a lace or tape to seal it.
Package Included:
- 1 x Braided Stainless Steel Carb Dual Inlet Line Kit. (100% brand new, never used or installed)
- 2 x O-ring seals
Stainless Steel Braided Rubber Hose
- The rubber oil hose is braided with stainless steel.
- Anti-corrosion
- wear-resistant
- high temperature resistant
HIGH STRENGTH AND DURABLE!
- Oxidizing
- Rusting
- Corrosion Resistance
Aluminum Alloy Joint
- Made of high quality aluminum
- Anodic oxidation process
- Tightly connected
- Good sealing effect
One End Connector Display
Straight fitting connect the tee with end plug head
Diameter Conversion Details Show
AN8 female inner wire to AN6 male outer wire
Other End Connector Display
AN8 tee connection reducer to AN6 display
Tony
Reviewed in the United States on August 9, 2024
Still working fine. Easy install.
Chris
Reviewed in Canada on August 29, 2024
As others have stated has to be cut down to size and don't crank on it to tighten. Only real issue paint is thin and starting to discolor
Customer
Reviewed in the United States on August 13, 2024
Good
High Tech
Reviewed in Canada on July 28, 2024
So far so good ,seems good quality and if it leaks ?Pretty sure it will just need some tweaks like most everything else does on hot rod upgrades.
Don Edwards
Reviewed in Canada on May 29, 2024
all the fittings are there but the person cutting the hose needs a new tape
Maxwell sterry
Reviewed in the United Kingdom on March 5, 2024
I had some issues, the small grub screw at the rear lower side on the duel feed, there a small grub screw which was loose and needed not only tightening but also Teflon tape to stop leakage. I was a little frustrated at having to remove the unit several time until l found the problem.
Chop 88
Reviewed in France on December 1, 2024
Produit inutilisable , ne peut pas s utiliser avec Holley 4150 ! Les Pas de vis ne correspondent pas ni les entraxes . A bannir .
NKYGUY
Reviewed in the United States on July 6, 2023
As others have said, this does not fit a Holley carb. Yes, it can be shortened but you really shouldn't have to at this price.Also, multiple fittings = multiple leaks !Would not stop leaking at float bowl connections.
goggles pisano
Reviewed in the United States on June 9, 2023
I had to trim mine like many others. Better long than too short.
Seckery
Reviewed in the United States on January 21, 2023
The quality is not worth the price Just like other ppl mentioned it's way too long needs to be shorten and there's a bunch of crap in it when they cut the hoses to make it. if you don't mind that it's alright I would recommend you take it apart and blow it out before installing
mike eads
Reviewed in the United States on August 11, 2022
Do not buy this product, leaks no matter what I did, I have been working on cars for over 20 years and this product is junk.
Brian
Reviewed in the United States on June 2, 2022
I like the part. Just when installing on the card the hose in the middle was just a bit too long and the hose was causing the front line to turn up. I took the line apart and shorten the hose a little. Works fine now. Would buy it again.
ArlenZ
Reviewed in the United States on May 24, 2022
This fuel line is of good quality, but a little longer than I need. So I unscrew by myself and make the braiding part a little shorter. Anyway, the length is not a big problem, still a good stuff with cheap price.
Recommended Products
$39.00
$ 17 .99 $17.99