Your cart is empty.
Your cart is empty.Product Description
Dust Collection/Collector Reclaimer System
High Quality Steel Materials
This dust collector is made of sturdy cold-rolled steel with powder coated finish that can resist rust and corrosion for long-term service.
2 Gallon Dust Collection System
With a generous 2 gallon dust capacity, the dust reclaimer can prolong operation without frequent emptying, which allow you to focus on your projects uninterrupted.
1.75 HP Powerful Motor
Equipped with a high performance 1.75 HP motor, the sand dust collector can capture traps particles up to 5 microns and collect media dust for a clearer view.
Product information
- Electrical Rating:120V/60Hz
- Motor Rate:1300W
- Noise: Lower than 75dB
- NW:14.3lbs
- Size:21.7''x9.3''
- Capacity: 2Gallon
- Material:Cold-rolled Steel
- Mounting Type:Wall&Cabinet Mount
High Adaptability
Designed with 2 inch inlet,the sandblast vacuum can fit most of media(sand,glass beads,silicon carbide,aluminum oxide,crushed walnut shells）blasting cabinet .
Dual Filter cartridge
Can reclaim media otherwise lost and keep dust out of your shop air efficiently and effectively.It will provide you a safe, clean work environment
Easy To Assemble
Insert the rubber sealing ring into the appropriate hole of the sandblaster cabinet and attach the dust collector kit with the provided screws.
Gamebler
Reviewed in the United States on September 9, 2024
Works great, but wear your ear protection for extended runs. Pretty loud.
Richard Reese
Reviewed in the United States on September 7, 2024
I've only used it four times before the reset button failed. It runs for about 15 seconds and then shuts off. It wasn't adjusted well from the factory and my first use it filled the entire garage with dust. Make sure the filter is tight against the housing. I would look at other units before buying this one.
Nick van Woert
Reviewed in the United States on June 3, 2024
The media could not be loaded.
Myron Jacobs
Reviewed in the United States on February 19, 2024
This unit has been installed on a sand blasting cabinet.Works fine.But do your self a favor do not purchase this unit.Reason? Because you can’t get parts, and most important the filter.WARNING NO AIRFILTER AVAILABLE!!!!!
Shawn
Reviewed in the United States on October 6, 2024
Thought this was going to solve my issue with needing to use a vacuum and vortex attachment.After 5 min of use I'm covered in 220 AO everything in my shop is covered with a coating of AO.Guess it's a good thing I can right this off on taxes cause I'm not impressed I'll go back to using shop vacs and vortex attachment.Thank God I wear a respirator while I do this
MJC
Reviewed in the United States on September 15, 2023
The machine works well, Only thing,the ad says it can be wall mounted, It can,but it is totally up to you as to how to do it because the instructions only show how to mount it to a blast cabinet.IT is very strong, I installed shut off valves on the intake line so I can use it on 2 blast cabinets, if you have a small table blaster cabinet with glass bead,it will put the media up from the bottom , so you will need to bleed off some of the vacuum either as a "leak " in the hose or other means, I just let it pull from the other cabinet as a way to keep from running the machine with the port blocked to much.
Eli Winterburn
Reviewed in the United States on November 16, 2023
The only quality thing about it is the powder coat finish other than that it is just a vacuum falsely advertised as a dust separator.
Michael H.
Reviewed in the United States on October 12, 2023
received in damaged condition. tried to contact, no response. spend a little more and get a much better brand. had to repair just to make it work.
Recommended Products
$209.00
$ 82 .99 $82.99