Your cart is empty.
Your cart is empty. Genuine Echo Fuel System Kit 21.2Cc Repower
Part #: 90098Y
Fits models: CS-290T
Heather Kerr
Reviewed in the United States on August 16, 2023
Be careful installing and note throttle linkage orientation and carburetor part orientation. Kit does what it’s suppose too. No more leaks!!
StrawberryHill
Reviewed in the United States on January 5, 2023
Frist, this is an excellent Genuine ECHO kit with all the needed parts ready-to-go! Here's the tough part, and a solution: the black rubber grommet/stopper/plug is hard to push into the gas tank hole. I found a way to make it easier: first remove the two shorter tubes (the vent, and primer return drain) while leaving the main longer fuel line (with filter) in place. Now the grommet can be squezed along the edge to get it in. I put some lithium grease on the grommet, put use whatever lube you have on hand. After gettting the grommet installed, re-insert the two lines that you removed. Next replace the circulat gaspket in the gas tank cap -- the gasket is included! Oh I have ES-210 blower-shredder but the method works on any make or model.
J-6
Reviewed in the United States on September 7, 2019
The old Echo PB-200 was showing the ravages of old age and gasoline with ethanol. Using this kit, I brought it back to life. Runs just like new. I had a bit of difficulty placing the grommet in the fuel tank but with the application of silicone grease and a few four-letter words, it popped in just fine.
Will7663
Reviewed in the United States on December 14, 2019
I didn't opt for the more generic items to update the fuel system on my Echo blower, insteade going for the manufacturer's offering. It is a bit more expensive then the generic offerings, but I'm pretty sure it won't degrade as quickly with our alcohol laced fuel. This fit perfectly, worked perfectly, and I now have a leak-free blower!THANKS!
Joe
Reviewed in the United States on July 17, 2015
Works as described. Remember to hold on to the little brass connector/splice that joins the filter/tubing assembly to the tubing that goes through the grommet and connects to the carb. The new kit does not have this piece. It's not a part that goes bad often. I didn't notice this piece inside the old filter tubing and almost through it away. Again, the black filter tubing that goes inside the fuel tank is the same size as the black tubing that goes through the grommet and to the carb. So don't lose this brass piece that splices the two lines together. Mine was stuck inside the old tubing. Also, put a good amount of grease on the new grommet before installing. It's hard to get into the tank, but fits like it should once it's installed. Tight and without leaks. Great part for the money.
kurt
Reviewed in the United States on July 10, 2014
Works great. Easy to install. Just make sure you keep track of the three hoses. I swapped two and it took me a while to figure it. Doh!
Kevin
Reviewed in the United States on May 22, 2014
This is a great product. It comes with everything I needed to fix my blower. You can't buy these at Home Depot. I tried instead they wanted me to buy a new one. Install was simple. My blower has never run better. I have already refered this product to friends and family who own the same blower. Thanks Echo for making parts to fix an old blower
loves to read
Reviewed in the United States on November 7, 2013
The kit was just what I needed to stop the fuel tank from leaking. I have used my leaf blower several times since installing this kit and things are just fine now and the fuel stays in the tank where it belongs and not all over your pant legs and fingers. My leaf blower was 11 years old, so the installation time and price of the kit were well worth the effort rather than spend perhaps 200 dollars for a new leaf blower. One last thing... a primer bulb was not included in this particular kit should you need one to make a repair of your own with the bulb being the issue.
Recommended Products
