Your cart is empty.
Your cart is empty. This listing is for 4 x New Chrome Illuminated Arcade Buttons
All the buttons are not metal.
If the LED does not light. Then please exchange the location LED interface.
Give your arcade project the wow factor with this translucent, illuminated arcade button. Each button comes complete with a fixing ring, bulb holder, spacer, microswitch and 12V LED.
If you decide to illuminate the LED supplied with this arcade button, you will need a 5V power supply. This can be taken from a spare molex connector (yellow wire) on a PC power supply or a Jamma PSU. This button will mount in a 24mm to 28mm hole.
What's included with this button?
4 x LED Illuminated Push Button
4 x Fixing ring
4 x 12V LED Lamp (We will add one lamp as a gift)
4 x Bulb holder
4 x Microswitch (We will add one Microswitch as a gift)
Product Dimensions:
* Mounting hole required: 24mm - 28mm
* Overall diameter of button across plunger: 32mm
* Maximum depth of button from top of plunger to bottom of microswitch: 65mm
Wiring Information:
These buttons require 4.8mm crimped wires for connection.
1 wire for ground connection (CO) and 1 wire for signal connection (NO).
These buttons require 6.3mm crimped wires for illuminating.
1 wire for the positive connection and 1 wire for the negative connection
Xevious
Reviewed in the United States on July 29, 2023
These are great arcade buttons. I used the player 1 & the player 2 buttons on my cocktail table. The only reason it gets 4 stars is that you will need to glue down the logo inside of the button or it will spin and never stay straight.
Terry Bates
Reviewed in the United States on February 17, 2023
I used this set and 20 more like colored buttons and micro switches to upgrade my X-Arcade Tankstick. We had to build a wiring harness for the 12 volt leds. Otherwise the buttons are a one for one replacement on the Tankstick. The threads of the buttons appear to be metal, while the rest seems to be chrome covered plastic. UPDATE: The leds were running too bright, so we reduced the led voltage down to only 5 volts dc. Picture uploaded.
Fran
Reviewed in Spain on December 29, 2023
Cumple su funcion
BryanBPH
Reviewed in the United States on November 30, 2023
I originally had non LED P1 P2 and Coin buttons, but rebuilt my arcade cabinet with LED buttons and paired it with LEDBlinky which is fantastic. Now when I launch a game, only the appropriate buttons light up making it easier for people to use my cabinet. I don't find the lights to be too bright, so they aren't distracting for me. They are just right. The buttons are durable and seem like they'll hold up for quite some time. I like the chrome finish around the button (fyi the red/orange color on the chrome rings is just a reflection from my other LED buttons that are lit but not shown in the picture)The only complaint, which others have mentioned is that the graphics easily rotate so they don't stay oriented properly. I considered opening them up and gluing like others have suggested, but honestly for me it's such a minor issue and my OCD hasn't kicked in yet for me to feel the need to fix it.Overall I'm very happy with these buttons and would recommend them if you want quality LED P1 P2 and coin buttons
Massimo Mancini
Reviewed in Belgium on November 19, 2023
Ok
Alessandro
Reviewed in Italy on October 28, 2022
nel complesso un buon prodotto, unica pecca le scritte girano ogni volta che si preme il tasto...per il resto ottimi e funzionali.
FILIPINOY
Reviewed in the United States on April 1, 2022
If you take a button apart by pushing the two white pieces in the back of the button towards the middle and pushing the white plunger out (hold the spring so it doesn't shoot out into space. Remove the cap, and look closely at the top side of the pluger, there should be 4 notches. The cap should have two nipples that go into the notches of the plunger. I noticed this cause one player start never moved. Use some superglue and glue the cap onto the plunger. orientate the plunger vertically with the cap since there's more room away from the 6 button layout. Now your buttons don't move :).
Den
Reviewed in Australia on March 14, 2021
Appears to be a quality product, but unfortunately the printing of P1, P2 and Coin is not centered and lets the product down - disappointing.
M(400HV) C.
Reviewed in the United States on January 15, 2019
Some people complain about the "images" rotating around while you bump the button or brush your finger next to it. It's not a deal-breaker. It would give the anal-retentive people hours of engagement. Or you could just use a dot of glue on the inside edge.
Steve
Reviewed in the United States on September 4, 2018
these are pretty low quality buttons. first the words appear to be pieces of printed paper inside the clear button and when lit up it petty obvious, so it just dosen't look that good. Second and more importantly the buttons rotate and are not fixed in place so the word on the buttons don't stay straight, they constantly move around when pressed. Again, a small issue that could have been easily corrected. I had to disassemble each button and put a small amount of glue on the button cap to keep it from spinning. Last, the LED terminals are not marked "+" and "-" so you have to guess and if you get one backwards then none will light up. Does not appear to do any damage, but you have to hook up one at a time and then check to see if the buttons lite up before moving on to the next. For the reasons above I'd look elsewhere for a better LED button if you really want your arcade panel to look nice.
Nick C.
Reviewed in the United States on August 1, 2018
Awesome arcade buttons! I used a plastic container to build a “mock up” before building one out of wood and metal. You can see in the pictures that I switched out the white LEDs and put Purple ones in there for now, and they are really easy to change. Besides looking awesome, they work great. Just like an arcade button should feel, but they have a slightly heavier push to them than regular arcade buttons, but that’s totally fine because you arnt using these buttons for playing the actual games, you use them to “insert coins” and “player 1 and player 2 start” so bottom line these buttons are great!
AIR
Reviewed in Germany on July 22, 2018
Leider drehen sich die Knöpfe in der Fassung.Nach 2 - 3 mal drücken muss man den Knopf wieder richtig drehen.NIcht gut gelöst...Die Mikroschalter in dieser Preisklasse sind wie üblich einfache Cerrys ( Also recht laut...)Ansonsten verlief der Einbau ohne Probleme.Wer die Stromkabel anlöten möchte, sollte vorher testen wo + / - ist.Es gibt keinen Hinweis auf dem Knopf.
Tony
Reviewed in the United States on March 17, 2018
I was going to return these because the 12v thing had me confused, so I had ordered 5v buttonsThat order got delayed and I had not shipped these back yet - so I decided to try it, and I am so glad I did.The look of these is very nice - the chrome with the spacer makes them really stand out compared to the just white onesClear instructions would be nice, but basically the yellow and black wires connect to the red and black micro switch and the red and black wires connect to the black bulb holder.If you hook it up the other way - all your buttons will turn off when you push this and it does not work as a button for the joystick
Recommended Products
