Your cart is empty.
Your cart is empty.Product Description
This extended version can reach the saw blade which 6.1 inch/155mm away from the T-slot. It fits most table saws,except Dewalt saw.
Lengthen Size
Supports most table saws where the mitre track sits too far from the blade.(Long still not enough to reach Dewalt saw blade)
Metric/Imperial Scale
Scales for both millimeter and inch are laser engraved on the anodized aluminum body to the same tolerance.
Slider was Locked to Screw Rod
That way you would only need to deal with tightening the knobs and not have the threaded rods come out of the "T" nuts, or bottom out in the slots.
Equipped with Slider & T Bolt
Fit 3/4 x 3/8 inch standard miter slots, 30mm and 45mm T-Slot Track.
Securely, Accuracy, Safety
Speeds Production
1. It slide easily into the T-slot and locks securely, firmly pressing the workpiece against the fence for clean and smooth cuts, get consistent thin strips,speeds production.
2. You can set the dimension of your strips without having to compensate for the thickness of you saw blade.
3. It keeps your fingers away from the saw blade, which greatly improves safety.
Using the thin rip jig is very easy
Steps for Usage
Step 1. Slide the jig into the T-slot of your table saw,extend the bearings until they touch the tooth of the saw blade, set the dimension of your strips and lock down. (without having to compensate for the thickness of your saw blade)
Step 2. Lock the jig a few inches in front of the saw blade.
Step 3. Lock your fence so your stock is just touching the bearings and make the cut.
Step 4. Repeat as needed,cutting consistent thin strips.
Don
Reviewed in the United States on March 8, 2025
No instruction, can't figure out how to use it. It's still in the box....
Foo4Fun
Reviewed in the United States on May 3, 2024
This works in the miter track of my SawStop ICS. With the rip blade I have installed, the zero point is at 7mm on the jig scale so plenty of breathing room to reach the blade carbides. I eyeballed a 1mm shim and ripped several strips, all are within .02mm of each other - easily as accurate as my needs require. The miter lock pieces are just slightly smaller than the miter track, so snug the jig to the left edge of the miter track when locking it down, and any extra pressure from your stock on the bearing once you lock your fence doesn't shift the jig to the left further.Great little piece of kit, good price, very solid and easy to use. Made my life much easier today. I'm a cabinet maker. I needed 1mm spacers for the reveal of inset dead panels on the ends of a vanity, which will be clipped into place with Lamello Tenso clips. I needed the spacers to be accurate and consistent as I'd be referencing the Zeta off of them. This did the trick.
Joseph DeMauro
Reviewed in the United States on March 4, 2024
The jig is solidly built…first thing is…your miter gauge slot MUST be two things. 1) able to fit the legs on this jig 2) Even if it fits the slot, the design may not allow the jig to clamp and stay put. I’m not a carpenter or even close to a pro, but I have a small craftsman table saw and the jig did slide, but will not clamp. Might be an issue on other small saws? I had to take the gauge off the track of my miter gauge apparatus and modify it to act as a “sled” by drilling two holes into it, and using the existing tapped hole…ground a compatible screw to a point…and used it to secure the “sled”. A lot of work when you can make a jig much easier. To be fair, many of the jigs like this are no different. But, if your slot is compatible with this jig, it IS solid, the bearings glide freely, and it seems to work. If it weren’t so iffy, it would get five stars.
DaveZZ
Reviewed in the United States on March 28, 2024
Well-machined, clear markings, works perfectly on a Delta Left Tilt Unisaw. With the jig fully extended, it will be 1/16" to the left of the blade, and the scale calibrations will be accurate. If need to rip strips thinner than 1/16", just move the screws holding the T-slot inserts to a different hole. You can then set up the jig initially with the bearing just kissing a blade tooth, and then move the jig safely forward from the blade, and readjust the slide to the desired rip thickness. It comes with no instructions, but you can download a manual for the Woodpecker Thin Rip Jig on their web site.
Catherine Tackes
Reviewed in the United States on December 16, 2024
Excellent product. A single knob adjustment is quick, accurate and repeatable. It is very stable and has a nice quality look and feel.
Conspicuous Consumer
Reviewed in the United States on November 4, 2024
It did exactly what I needed it to do. Fit well on my table saw (Metabo 10"). I was able to consistently rip very thin pieces of wood to use as edge banding.
Stephen McBride
Reviewed in the United States on October 13, 2024
Mainly writing to inform that this version doesn’t fit the Shop Fox W1888, it stop about 1/4” from the blade when fully extended.Already ordered the next extended version because the quality was good and fit perfectly in the T-track of the table. Looking forward to using the longer version.
Walter Ireland
Reviewed in the United States on February 13, 2023
I love this tool....makes creating thin strips with a table saw so so easy and accurate.My unit arrived on time and in great condition accept the T-nuts that hold it in the slot on my table sawwere not the correct size. the bottom fit ok but the top of the T-nut would not fit the groove.It required me to put the T-nuts onto a Mill and mill the top of the T-nuts to the correct width inorder to work with my table saw. Not a problem for me as I have friends, but for some woodworkers, this could end up being a problem that results in an unhappy return.
Recommended Products