Your cart is empty.
Your cart is empty. Fender Eliminator Kit for Triumph Daytona 675 675R 2013-2017, Daytona 765 Moto2 2020-2021, and Street Triple 765 R/S/RS 2018-2024
[Version 1.2]
Features:
Revised design - now compatible with more international license plates - see specs for fitment
Direct bolt on installation
Compatible with OEM* or aftermarket turn signals utilizing 10mm hole mount using included optional adapters
Mounting hardware included
Includes plug and play white LED license plate light
Precision CNC laser cut 304 stainless steel and powder coated satin (textured) black
*OEM turn signal brackets may not be compatible with international plates
Installation instructions can be downloaded on our website
Over_9000
Reviewed in the United States on March 9, 2023
First of all, thank you MD for responding to my question right away! I ended up purchasing this after reading a few answers. I rarely do any mods to my cars or bike, because I’m worried that I’ll make a mistake somewhere. But this one was extremely easy to install and seems high quality too IMO.
zach
Reviewed in the United States on June 20, 2022
Loved it worked perfectly.
Chief
Reviewed in the United States on September 28, 2021
Fits my 2020/21 Triumph Daytona 765 if anyone is curious. Bolted in with no problems and wiring was straightford.Easy clean up of the rear fender for sure.
Dtrux73
Reviewed in the United States on January 14, 2021
Installing this kit is relatively easy. I installed mine on a 2014 675R. Since nearly everyone will be doing this for the first time, the more difficult steps actually relate to the Triumph its self. Once you get the REAR seat off, it is easy to see three of the four bolts that hold the whale tail on. The fourth is a bit hidden and is toward the front of the bike. Also the wiring connector comes apart easily.If you intend to re-use the turn signals, it gets more interesting. The whale tail uses a variety of sizes of fasteners and two of those are hidden under the rear reflector. You will need some allen wrenches and small sockets.You will also need to reuse the electrical harness that supplies power to the turn signal and plate light. On my bike the connectors were greased and I could not get them apart. I ended up cutting the wires and then using my own connectors. Later I played around with the stock connectors -- if you clean them up you can probably coax them apart if you push the tabs in with a screw driver ahead of time. That is what I would do if I installed another one. Also, the wires are different colors for left and right on the harness, but not on the lights. So make sure you write down what color goes to each.The holes that the bracket mount to, are also the holes that the license plate uses. So you may have to remove a couple of them again to put the plate on.Finally, the whole assembly seems to be made of steel Very strong, but way too heavy for what its intended to do.
Ivan Alvarado
Reviewed in the United States on May 21, 2019
Pretty easy install, cleans up well and looks amazing! 10/10
Trevor O.
Reviewed in the United States on February 9, 2019
Purchased this fender eliminated kit along with the motodynamic integrated tail light. They go together on my Strest Triple R, FLAWLESSLY. If you do both of those mods, I recommend doing them at the same time. You gotta remove one to get to the other. Finished product looks freaking awesome. 10/10
SB
Reviewed in the United States on June 9, 2016
Excellent product, easy to install, you don't even have to splice any wires - all plug and play.Enhances the look of the bike, over all, , highly recommended.
Matt
Reviewed in the United States on March 13, 2016
Downright excellent product. Installation instructions are quite clear, but some pictures would have been helpful. But the end result is just beautiful. A heck of a lot cleaner than the OEM fender, and the LED license plate light does wonders for visibility at night. I've received nothing but compliments on it. I could not be more satisfied.
Recommended Products
