Your cart is empty.
Your cart is empty.ACDelco GM Original Equipment Power Seat Connector is a GM-recommended replacement component for one or more of the following vehicle systems: ignition, starting and charging, body-electrical and lighting, and/or engine fuel management. This original equipment connector will provide the same performance, durability, and service life you expect from General Motors.
Aaron G.
Reviewed in the United States on January 25, 2025
Excellent
chuck c.
Reviewed in the United States on January 19, 2025
This is not a pigtail, it is just the receptacle. A pigtail has the wires attached to the receptacle. Very disappointing to advertise it is a pigtail then received it and can't use it.
Customer
Reviewed in the United States on March 16, 2024
Works a advertised
William J. Hutchinson
Reviewed in the United States on November 18, 2024
Repaired my heated seat with no problems
John
Reviewed in the United States on November 9, 2023
It is much easier to buy this product with the wires all ready in the plug connector also a lot cheaper in the long run Anina WPT928 Wiring Kit Heated/Cooled Seat Module Connector Wire Assembly for 2003-2019 Ford F150 F250 Explorer Mustang Fusion Lincoln MKS Mercury Milan 12 Leads Wiring Harness 3U2Z-14S411-ZMB WPT-928 this produce fits your Cadillac DTS I installed one in mine this past week seat heating and cooling working fine now
Utah
Reviewed in Canada on July 12, 2020
Did not come with any wires as picture showed
Bob C.
Reviewed in Canada on February 1, 2020
This was the correct plug for the above application however trying to find the correct terminals to go in it was a challenge. The recommended ones on Amazon are not the right terminals and will not fit.
Jared Johnson
Reviewed in the United States on March 1, 2018
Worked great as a replacement connector for my 2011 Expedition seat heater module. Motorola makes the seat temp module for both the GM and Ford SUVs for this period.
JD
Reviewed in the United States on December 30, 2018
If you are doing this repair, you will need the pins and the crimping tool, and by the time you spend that 30 to 40 bucks, you might as well just spend the 40 bucks and get the wires/connector assembly (link below) instead. It's not as easy as you think to replace pins on wires, even for someone who has experience with cables and connectors. It is much easier to just splice and solder the wires together and heat some shrink tubing over them.https://smile.amazon.com/gp/product/B0031H2FES/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
JohnWells
Reviewed in Canada on November 18, 2018
After a bit of research, I found that a common reason for heated/cooled seats to fail in DTS and Escalates (and Ford Expeditions which oddly use the same hardware) is a burnt connector at this point. The burnt connector melts this pigtail, forcing you to cut it off and replace it. On the DTS, this connector is under the passenger seat, though it needs to be intact for heat/cool to work on either front seat.As well as this item, you will need 8 x 14ga (Mouser 829-15304711) and 2 x 12ga (Mouser 829-15304713-L) connectors. I couldn’t find them anywhere, and had to order directly from the manufacturer online. Make sure you order spares, the 12ga connectors are difficult to properly install.On my DTS, I found it much easier to remove my seat to do this work – I had to also order a T-50 socket to remove the seat. I also added some dielectric grease to reduce the chance of the connection failing again in the future.The repair took me around 1.5 hours including the time to remove/replace the passenger seat. I’m happy to have my heated seats back in time for winter!
JMP2005
Reviewed in the United States on January 26, 2018
I used this to replace the burnt plug on my 2008 Cadillac Escalade heated seats. Also purchased the pins that go inside the plug. Cut back the old wires, crimped on the new pins and inserted into the plug. Easy. Took about 1hr for the complete repair.
Recommended Products
