Your cart is empty.
Your cart is empty.Product Description
Install the dual seal onto the end of the injector
Used for replacing the fuel injector O Ring Seals
- Includes two seal installation pilots for each groove, a seal installer driver, and a compression sizer.
Ensure proper injector installation
- Installs the dual seals onto the end of the injector to ensure proper injector installation.
Package Content
1 X Seal Sizer
- EN-49245-4
- Drive the seal over the pilot and into the groove.
1 X Seal Installer Pusher
- EN-49245-3
- Compress each seal into its groove and ensure its size prior to installation.
2 X Seal Installer Guide
- EN-49245-1 Long Seal Installer Guide
- EN-49245-2 Short Seal Installer Guide
2 X Seal Installer Guide
- 1 x EN-51105-1
- 1 x EN-51105-2
- For 2013-Newer Bosch, Continental, Delphi SIDI Injector Seal Installer Adapter Alt
Step To Step Installation
Step 1
- Cut off the damaged teflon seal near the tip of the injector.
Step 2
- Place the Seal Installer Guide on the tip of the injector, then put the seal on it.
Step 3
- Use the installer to push the seal into the groove of the injector.
Step 4
- Use the sizer tool to compress the teflon seal to the correct size. Then the seal are installed correctly and sized correctly for leak-free operation.
Bob Sikma
Reviewed in Canada on November 18, 2024
The injector siezing tool will not work on gm 5.3 ltr injectors, it to small, this makes this kit useless. The add says it works on the gm aplication but they are not honest.
Nicholas
Reviewed in Canada on October 18, 2024
The bore of the die to shrink the seals has no taper at all so it just mashes the edge face of the seal. Worth the money to get the tool made by Lisle, GB remanufacturing, or CTA tools.
Jake Hemmah
Reviewed in the United States on April 28, 2024
Worked as well as a high-end tool.
E.J.
Reviewed in the United States on April 12, 2024
This product did not fit the seals correctly but instead tore them and/or stretched them further.
doug morley
Reviewed in Canada on July 12, 2023
used tool to replace injector seals on 2017 subaru forester 2.0l turboo
letsgo2
Reviewed in the United States on June 2, 2023
the cones are perfect on this. the plastic pusher is almost useless, but with the cone, you can push the Teflon rings on by finger with no issue at all, just lubricate it with a silicone-based lubricant. The compression tool took some machining with a 5/16 drill bit to get it to be right and not deform the o-ring. after that, every single one went on smoothly. Overall, good tool and, crucially, I was able to get it in time to do the job with next-day shipping.
santana
Reviewed in the United States on October 30, 2023
good
Customer
Reviewed in the United States on April 12, 2023
This tool does NOT work. Expanders are too big for injectors and oversize the teflon seals. Sizer bore is not smoth and cuts seals. DO NOT BUY!!!!!!
Geoff
Reviewed in the United States on July 2, 2022
This works great for 5.3/6.2L GM v8s. The expander works flawlessly and quick.The seal shrink tool does work, it's just not instant. You have to put it on the seals, let it sit at least 15 minutes per seal. At least 30 minutes total.I started the shrinkage process and installed 8 spark plugs. By the time I was done the seals were set. Actually shrunk smaller than OEM.
Russ
Reviewed in the United States on May 4, 2022
I bought these to do eco tech injectors and it worked great I bought the kit so I had all the tips as I own a shop and will uses them sooner or later
Derek
Reviewed in the United States on January 28, 2022
This also worked great on KIA/ Hyundai 2.0/2.4 GDI injectors. Easy to use and good results. You cant beat this kit for the price! I would highly recommend this to anyone doing GDI injector seals!
Recommended Products
$64.99
$ 29 .99 $29.99