Your cart is empty.
Your cart is empty.1.Achieve Flawless Edges: Transform rough edges into smooth perfection effortlessly with Deburring Chamfer Tool. 2.Versatile Applications: From Stainless Steel to Wood, our tool handles a wide range of materials. Empower your DIY projects and professional tasks with confidence. 3.Precision Counts: With a wide size range from 1/8" to 3/4" ，our tool not only deburrs but also features a countersink function, ensuring clean and accurate finishing for your projects. 4.Simple and Safe: Effortlessly attach to your power drill for quick results. Its safety design protects your hands, leaving no room for sparks or burns. Recommended proper speeds and feeds (0-400 RPMs) 5.Built to Last: Crafted with high-quality HSS / Tungsten blades, durability is our promise. Experience lasting performance with a tool designed for perfection.
Dan A. Williams
Reviewed in the United States on January 9, 2025
Thank you for checking out my review. Hope you find useful information.I’m going to try not to rehash information that is available in the ad itself, like basic pictures of the item, all the accessories, and basic uses for item. You are here looking for a solution to your issue at hand. Mostly I want to point out any problems that I see , things that can be improved , areas that it falls short. Thus to further help you with your decision of whether to buy it or not to solve your current or potential future situation, with all that, hope this helps. Functional little units , decent quality. Hard to tell in the picture but the black one was not tapped into the main unit correctly so it’s crooked but the blue one is fine. That’s why I took the close-up picture. they’re functional. They seem to be sharp. They’re holding up pretty good, are there others out there That are probably better quality, yes but you’ll probably pay a lot more for them . so it’s always about the cost benefit ratio. Hope this helped.
Good seller thanks for your help
Reviewed in the United States on January 25, 2025
Haven't used them yet but they look great. Fast shipping good price good quality good seller.
Yordel Hernandez
Reviewed in the United States on January 2, 2025
Excelente
vernon doom
Reviewed in the United States on September 25, 2024
this is trash go with a more expensive part from a different manufacturer.
Ramon Ortiz Aguirre
Reviewed in the United States on August 22, 2024
Tal y como se muestra en la publicidad.
jorge aguilar
Reviewed in the United States on May 20, 2024
Me ha trabajado muy bien
R. Hyder
Reviewed in the United States on December 29, 2024
Nice chamfer tools. Personally, I don't think you can go wrong with carbide...IMHO.So far, I like them and have used them to clean burs from bolt holes and the angle is good to countersink for bolt heads as well. I don't have much call for the OD chamfer tool, but it does look like it is made well and would work just as well as the ID tool. They are all sharp and cut well.I needed a set to keep in my drill/impact box. Since these have the hex head, they will snap right in my impact tool to make for quick tool changes as needed.I like these a lot and so far, they have worked well and held up. It is a nice set. I found a small box to keep them in so I do not lose them. Easier to keep you with them that way. Going to see if I can find a box to keep these and my most common taps in as well.
WD
Reviewed in the United States on November 19, 2024
These deburring tools work well for their intended purpose. The blue cup shaped ones seem to work better on larger diameter bolts than they do on smaller diameter bolts, only because they center better on the larger bolts. My first few attempts at deburring the end of a 1/4-20 bolt resulted in the tool getting off center and wobbling around instead of being properly aligned. I think these two cup shaped bits would be better if they had 5 blades in them instead of only three. Five blades would allow the tool to center more easily on small diameter bolts. On larger diameter bolts, say 3/8" and above, this wasn't a problem, and even on the smaller bolts, if you take your time and get the tool centered on the bolt properly, they work fine.I liked the way that the three pointed bits worked. These have five cutting surfaces on them and that results in nice even deburring of holes. I used one of these to deburr holes that were drilled in a polycarbonate sheet, and they did a great job. These can even be used to countersink holes.The blades on these are nice and sharp and do a good job removing metal, unlike some other deburring tools that I have. I think that these are going to see a lot of use in my shop.
Recommended Products
