Your cart is empty.
Your cart is empty.
Features:
This quick release ball pin is lightweight, portable, convenient to carry and store.
Thanks to choice metal, the locking quick release pin is practical and stable, corrosion resistant, allowing you to use it with confidence.
Our spring plunger works well for rolling toolbox, mould, chassis, cabin, electrical appliances, industrial equipment, automotive, also can replace and change the key ring pin.
No threading or tapping required, steel quick release pin is easy and fast to apply, time and energy saving.
Specifications:
Color: as shown in the picture
Size: 1/4 inch - 20 thread size, 0.500 inch thread length
Material: metal
Package includes:
2 x Hand retractable spring plungers
Warm notes:
Please allow slight dimension error due to manual measurement.
Please allow slight color difference due to different monitor.
Small parts are included, please keep away from children under 3 years old.
jeff
Reviewed in the United States on March 8, 2025
smaller than I expected, good product
Tom
Reviewed in the United States on February 9, 2025
These little thumb set stews are amazing and a necessary part that j think all Milwaukee pack out users could use. I have roll over cover on my truck but the handle on the main big rolling bin is too tall to be able to close the lid all the way. Install these in place of the screws that hold the handle and now you can easily remove and replace the handle at will.
jol
Reviewed in the United States on July 16, 2024
The media could not be loaded.
Get Real
Reviewed in the United States on October 27, 2024
The description says 1/4-20 and 6mm which one is it... That's why the three stars; otherwise, the part is works fine. By the way the threads are 6mm.
おつむ
Reviewed in Japan on August 27, 2023
画像のような切込みが無く、くるくると回ってしまって用途が分かりません。クソです
Daniel M.
Reviewed in the United States on August 20, 2023
I purchased this to install on my M1lwaukee Packout rolling tool box (the smaller one) so the handle can be fully removed for transporting in the trunk of my car. It worked great! It makes it so you don't need any tools to remove and replace the handle. Jut pull on the pins, turn them slightly so they stay out and you can slide the handle out. Just as easy to reinstall it
Greg
Reviewed in Australia on July 3, 2023
Used a 5mm drill to open the hole a bit bigger, and tapped the hole with a 1/4 UNC. Didn't need the nuts, but they can be used if you mistakenly make the hole too big. Only had to enlarge the hole on the chest since the pin fits the existing hole on the railing.
Customer
Reviewed in the United States on June 7, 2023
I built a custom end table with removable legs for my RV. Needed a table that I could stow in small places with the legs removed and stowed inside the table. I need something to hold the legs in place when moving the table around when set up. I 3D printed the leg brackets and used the pins to secure the legs in their brackets when installed. Worked great. They have a nice, solid feel and snap securely into place or pull & twist to disengage. Look great as well.
Twofisted33
Reviewed in Canada on June 1, 2023
Exact same as neat at half the price
Jay Heckstetter
Reviewed in the United States on May 8, 2023
Good concept but not strong enough. The install was incorrect and needed to purchase a metric tap to drill into the packout case. There is no way to install them by threading them into a drilled out hole. They are not sturdy enough to tap themselves in.Once installed then needed to enlarge hole in handle to accept pins so it locks in place.Thought it would work good but one of the pins broke using it for less than a week.Replaced with bolts until better quality pins are available.
David Wilcox
Reviewed in the United States on March 9, 2023
I followed the other post and made the hole in handle a little bigger 5/32, drilled hole in plastic 3/16, tapped plastic m6 x 1.0 worked great but found that its still a little short to use the nut. With it not long enough if I pulled back the plunger it would loosen up and not be the same depth. To fix this issue I set the nut over the hole and used a soldering pencil to heat it up and press it down into the plastic.
Albert o.
Reviewed in Canada on April 4, 2023
This is a great mod to yourMilwaukee packout rolling tote. The tote handle can be removed to fit in a truck bed with a bed cover. The handle should be reverse dented so the pins can easily seat into the holes. 1/4 turn of the pins and they stay out so you can slide the handle down. Another 1/4 and some wiggling of the handle the pins pop in. I used 13/64 drill bit to enlarge the holes and a regular M6 X 1.0 bolt to make my thread and these just screw right in.
Frederic tremblay
Reviewed in Canada on April 30, 2023
Elle casse facilement et les filer mentionner ne sont pas les bon
Recommended Products
