Your cart is empty.
Your cart is empty.SmithJeremy
Reviewed in Canada on August 22, 2024
Some peopIe said I needed these for my 2022 f150 with halogen lights when installing LED bulbs. Didn’t need at all and stock boots worked great. I bought the sealight LED for high low and fogs. again you don’t need for standard LED bulbs on ford f150 with halogen lights.
R G
Reviewed in Canada on December 23, 2024
Was able to install LED lights and keep them dry with these
April's Showers
Reviewed in the United States on February 20, 2023
It was relatively easy to install. It fit’s good and works so much better when using LED bulbs. I could not used the stock ones with the new and improved LED lights.
Alan
Reviewed in the United States on April 16, 2023
I thought I was buying the one I see in the picture in the ad. However the ones I got have no ears on them, it’s just a cup to cover the 3 1/2” opening. It fits, but I would’ve liked to have the flange/ears in case I had to replace the headlights. It would be easier to take off, if I needed too.Other than that, I guess it’s ok for the price
Customer
Reviewed in the United States on April 11, 2021
Worked perfect on my 2017 F150! The high beam led bulbs sat centered and low enough in the headlight housing to reuse the factory dust covers, but the low beams were a different story.... the led bulbs I bought had fans on the back which once installed sat about flush with the housing which did not provide room for cooling with the dust cover on, plus they didn’t sit centered in the hole, they actually almost touched the top of the hole, so the factory dust covers wouldn’t seat all the way around.These covers give plenty of room for cooling, plus they fit around the outside of the housing instead of the inside, which was perfect for my problem! About the only negative is they are a little thin, although I don’t foresee that being an issue. They weren’t too easy or too hard to get on, so hopefully they will keep sealed well, I will update my review if they do not. Very happy for now!
Matt
Reviewed in Canada on April 1, 2021
Too soft which made difficult to install.
David D.
Reviewed in the United States on May 15, 2020
I have a 2019 F-150 and upgraded the pretty lousy OEM lighting with GTR Ultra 2 LEDs for HB, LB & Fog Lights (great LEDs BTW). The GTRs have a fan heat-sync and are a bit larger than OEM and just fit within the LB housing (top one) with about ⅛ to ¼ inch spacing. This isn’t enough space to reinstall the Ford OEM dust covers. Enter these dust covers...they fit perfectly: snug, secure and reassuring to me that dust and moisture won’t be entering the headlight housing and damaging my new LED headlights. If you find yourself in this situation, don’t lament - get these and you’ll be super happy about the quality and fit.
Matt B.
Reviewed in Canada on March 12, 2020
Bought LED for my 2020 F-150 XLT, so figured I’d allow them as much space as possible to dissipate heat. I put the caps on the dash of my truck to heat up for easier installation. Driverside was a breeze, the passenger side was trickier as I was using my off hand to reach up in the wheel well AND the Washer fluid tank and hoses run tight against where the cap is to sit. So I started from 9 o’clock position working my way back and was able to just get it on. They seem to fit well, not nearly as well as OEM, but I’m not concerned with them coming off at all.
Luis l quiroz
Reviewed in Mexico on February 18, 2020
Tardo demasiado en llegar
MrDecepticon
Reviewed in the United States on June 6, 2019
Purchased these to compensate for longer LED hgh beam lamps (H11/H9) as they stick out too far for the OEM dust covers. Matched the internal diameter. These are supposed to fit OVER the opening but fails to do so in my 2015 Nissan Rogue as the lip is obstructed in one section. Completely useless to me but still may work for other makes/models.Gave 3 stars as the quality is there and the item is as described. I think the manufacturer/seller needs to list what models this will fit and which ones it wont.
JFM1821
Reviewed in the United States on June 18, 2019
Needed bigger dust caps for my 2018 Ford F-150 which I installed new LED bulbs for both my lower and high beams in headlight. The factory dust covers are great if you are using factory a Halogen bulbs. LED bulbs with the cooling fans don’t allow the factory flat style caps to seat perfect. With this heavy rain recently my passenger side headlight has been getting moisture. When removing the factory dust caps I’m finding water underneath. Tried other dust caps and they didn’t fit properly, these actually fit with a little hand work behind the fender to access the headlight housing, low beams were harder to install then high beam just simply due to the tightness behind the lamp. Will see if the moisture stops now with these. Also helps with adding room behind the LED bulbs cooling fans so now they can breath alittle bit. Since heat is an LED’S worst Enemy! Hopefully these will keep moisture out! As for fitting on a 2018 Ford F-150, these 83mm fit great! Don’t even have to use any tie wraps with these, once there on they aren’t going anywhere.6/29/19 Update: these rubber dust caps work!! I had water moisture in my left headlight due to oem caps not sealing enough due to the extended cooling fan on my LED light bulbs. These caps sealed so good they caused the moisture not to escape! Had to remove and let the moisture dry first then reinstalled caps. After that the headlights have not gotten any moisture in them since even through heavy rain or car washing. Also allow better airflow for cooling fans on my LEDs which I have in both high and low beams. Worth every dollar they cost.Update 7/20/19: have had these dust caps for awhile now on my 2018 Ford F-150. In the beginning I was getting even more moisture in my headlights but that’s because these dust caps were working so well and I had moisture in the headlights still from when I had my oem dust caps. So I had to take them off and let the headlights dry completely, then reinstall the dust caps. Once I did that I have not had any moisture what so ever! And it’s raining season in Florida and I am constantly washing my truck. I use to get moisture in then all the time due to my upgraded LED bulbs which are bigger then oem bulbs and were causing the dust caps to not stay on completely letting in some water. Not the cause now.
Anonymouse
Reviewed in the United States on November 19, 2019
Installed on 2015 F-150 with factory halogen headlight assemblies as part of an LED conversion. Stock halogen H11 and 9005 bulbs my truck came with very shallow and used very shallow rubber socket covers. The LED are much larger due to the heatsinks and driver packs they come with. These aftermarket rubber caps fit perfectly and the added space afforded by the very tall domes gives plenty of room for the heatsinks and the drivers. My assemblies are pretty sophisticated design and have lots of dead air space between the individual reflectors and the exterior of the assembly so I am not concerned with heat being trapped. Other wise I would have looked for a rubber seal that sealed around the heatsinks while allowing them to poke though the center for ambient air cooling. Anyway, these are the correct diameter and height for my F-150 reflector style LED bulb conversion. Just be sure to secure them with a tight zip tie wrapped around the cuff.
Kristie H.
Reviewed in the United States on October 29, 2019
These are a must if you are putting LED headlights in a 2015 Ford F 150. It was a little tricky to get on. Start at the top and then slide it down to apply. The 83 mm fit the high and low beams. The covers will allow you more breathing room for the LED fans.If you want an extra layer of protection I put a thin film of silicone around the edge then install. This not only ensures that the dust cover stays on but it also makes an airtight seal to keep out dust and moisture.
Recommended Products
$49.99
$ 23 .99 $23.99