Your cart is empty.
Your cart is empty.Product Description
Protect Your Bike!
Your new bike looks great, but it won't last long. The more you ride your bike the more damage it will get from cables, road debris, and your own shoes. Protect those vulnerable areas with a thin layer of protection. After applying our Lamin-x Bicycle Frame Guard, your bike's paint will be safe and secure. Our Frame Guards take the damage so your bike doesn't have to.
Lamin-x's Protective Qualities
Lamin-x film is made from a 8 mils thick urethane that is designed to take the abuse that your bike would normally take.
The film absorbs damage from:
- Small impact damage
- Sandblasting
- Scrapes from chains, cables and shoes
Esau Ferrera
Reviewed in the United States on January 10, 2025
Desde que lo empecé a usar, todo ha cambiado para mejor. La simplicidad y efectividad con la que funciona es sorprendente. Me ahorra tiempo, energía, y el resultado final siempre supera mis expectativas. Realmente siento que mi vida es más fácil y organizada gracias a esto. No puedo dejar de recomendarlo, ha sido una verdadera revelación para mí.
M. T.
Reviewed in the United States on October 30, 2024
Getting a new bike is fun, but worrying about it getting ding-ed is not. Frame tape to the rescue! The instructions, that you need to use soapy water, are for real, don't skip this. You can make adjustments easily while it is slippery. Plenty of tape for my purposes: underneath the cranks, behind the down tube where a lot of spray hits, even up front where the brake cable rubs while executing tight turns. This tape is invisible from about 3 feet away. It's not going to stop a big rock but I believe it will help make that chip be a lot smaller than with anything to protect your paint job.
Joe
Reviewed in the United States on May 11, 2023
I had good success applying to one bicycle, not so much on the second. The material is relatively thick and seems to protect well. I made the mistake of applying too much water to apply and then had trouble getting a smooth finish. It is also a little tricky to cut appropriate slits for wrapping around corners, but with a little patience it worked out. Over all I think this is a solid product. Will buy again and hopefully my application skill is better.
djbike97
Reviewed in the United States on February 10, 2022
It's a total pain to install correctly. I don't think it's worth the trouble for the cost.
George M
Reviewed in the United States on September 8, 2021
Easy to install once you get the hang of it. Protects frame areas where a cable may rub or where you have a bag strapped on. Added some under down tub where dirt and debris hits from the front wheel.Will have to wait and see how long it lasts. Nice that it doesn’t hurt appearance as you can barely see it.
Joseph DiGiorgio
Reviewed in the United States on June 3, 2020
I am new to the MTB world and I thought it was extremely important to protect my brand new bike.Biggest tip is make sure you have a heat gun(or hairdryer) when applying. It really helps in the corners and with getting the edges to stay adhered. If you notice imperfections or lots of bubbles during installation simply just peel it off, respray and start over.This is not as easy as installing prefabbed stuff and it will take you a few hours but its not that bad! grab a beer or 5 and enjoy working on your own stuff.MUST BUY, 3m 2228 mastic tape, put it on your chain stay and bottom bracket. Makes your ride much quieter and saves the frame from any brutal hits.Thank you Lamin-x for a great product, hope to try any other products you may have
It Be Like That Sometimes...
Reviewed in the United States on December 4, 2020
Overall a good product and its easy to install it just takes a little time. Once you get the hang of it though, it's pretty painless and easy to install. Use a hair dryer for the ultra glossy finish.
Gerardo Paje
Reviewed in the United States on April 8, 2020
Really impressed with the quality, easy installation if you read the instructions and maybe watch a couple of YouTube vids before install. Comes with a exacto blade, small water bottle and squeegee to help with install. I recommend a large ruler to help with straight cutting the film fit along with a tape measure.You first measure your frame and cut a piece to fit. Make sure you trim the corners with scissors and make them rounded so they don't catch and pull in the future.Then clean the frame where you are going to apply the film. Remove the film backing, spray soapy water on the film adhesive side and also a little on the frame. Then apply and center. Then use the squeegee to smooth out and remove any water bubbles. Works well on rounded edges as well, a good idea to have a hair dryer or heat gun to help with that.
Recommended Products