Your cart is empty.
Your cart is empty.Product Description
Measured by hand Picture unit: IN
Inner Diameter (intake side): 36mm/ Outer Diameter (intake side): 42mm, Inner Diameter (air filter side): 54mm/ Outer Diameter(air filter side): 59mm （Manual measurement please allow a little deviation）
For SUZUKI LTZ400 LTZ 400 QUAD ATV
- 2003
- 2004
- 2005
- 2006
- 2007
Easy to install
safety
Premium
Services
Jay Wilson
Reviewed in the United States on May 16, 2024
Made my LST 400 run like new again. I did have to swap out the cruse jet and main jet. Stock jets where good if you are running a stock quad, mine was modified.
Mike
Reviewed in the United States on November 15, 2024
Fixed my issues. Wasn't the cheapest and dang sure wasn't the most expensive. Gave me my power back.
Tomy Mayer
Reviewed in Canada on March 14, 2023
Does not work
Guy
Reviewed in Canada on November 19, 2023
Throttle cable is NOT a matchWaste of time and money
paul mizik
Reviewed in the United States on January 16, 2023
05 kfx 400 is running great with this. Like all the other reviews, the throttle cable is in the wrong position. I read through the reviews and knew I'd have to do one of modifications mentioned in the reviews. There's 2 options or flat spots on the OEM carb and this carb (identical) for where the throttle cable tube can be pressed in. I simply drilled a hole with a drill bit the same size as the OEM tube in the second spot to match the OEM carb. Pulled the throttle tube off the old one with a vice and pry bar and finnessed it into this one with a little hammering. Works perfect and I didn't bother checking the jets or anything. Probably took 10 minutes
Casey Lesley
Reviewed in the United States on April 4, 2023
Had large fuel leak. Way to small of jets will run way lean .Found problems with the metal seat on fuel bowl replaced with rubber one and re jetted to make it work . But you get what you pay for! Cheap ain’t good and good ain’t cheap!
Nicky
Reviewed in Canada on July 15, 2022
Après quelques ajustements ,le carburateur fait la job.
Marven Brideau
Reviewed in Canada on June 15, 2022
part will be returned did not fit and i would not recommend this part cause of you would have to do to many changes to make it fit.
michael sturms
Reviewed in the United States on February 25, 2022
Carburetor was an exact fit except for throttle tube on carburetor is longer than factory one. I tapped threads down as far as I could cut some of it off and works perfectly now
Desertrider
Reviewed in the United States on November 23, 2021
Same as other reviews about throttle cable being too short and hitting the frame. Used die with same threads and threaded all the way to the bend on the outlet. Then used a tubing cutter to cut about 3/8 of an inch off. Filed down the ends of the cut and used die to clean up the threads. Routed the throttle cable under the frame and attached the cable to the carb. Before connecting the cable make sure the thrumb adjustment is all the way in and cable adjustment is screwed all the way to bend by the lock nut. Take your time connecting the cable it can be a pain. After connecting the cable check the thumb adjustment by watching how much free play the cable has at the connection on the carb. There will be very little free play but this will allow the throttle plate to close. With everything in place, the throttle cable will have a sight bend that touches the frame but does not interfere with the operation of the cable. The bike started up fine and can adjust the idle with no problem. The bike revs just like new runs good in the back yard but will need to take the bike on a long ride. So far so good.
Moving Experts
Reviewed in the United States on October 14, 2021
Fit perfectly and works good
Brandon
Reviewed in the United States on October 23, 2020
First off this is a China made carb but for it being made in China everything is almost spot on twitch except 2 things. The hole for the throttle cable inlet is in the wrong position and the inlet stem is not right either and the position it’s in you can not use the oem one because I tried it and it does not work and the only way you can use it is if you notch the frame on your atv and you have to use the inlet they provide and it’s to damn long and there isn’t enough adjustment for the throttle cable at all and your atv will idle high no matter what. But my z400 fired right up with it after I did a valve adjustment. I put my oem carb back on only thing this carb is good for is parts other then that stick to oem
Recommended Products