Your cart is empty.
Your cart is empty.Product Description
MSCRP Swivel Neck Thermostat Housing for K-Series K20 K24 radiator hose k swap
The housing swivels, allowing you to position the water outlet angle before it is tightened down.
The provided custom made fitting is the same size as the oem rad hose on one end, and is threaded for an AN fitting on the other end.
This allows you to use whatever size fitting you need for custom installations. If you want to use braided hose with AN fittings, this housing will bolt on easily and with the right adapter threaded in, you’ll be all set.
The swivel neck comes pre-assembled with a quality Stant thermostat (180 deg °F) which is held in place with a 'C' clip.
Adjustable, set the rad hose at any angle.
Fan switch port for engine swaps.
Easily deletes heater core hoses on race cars.
Threaded water outlet for custom setups.
The kit uses a standard size thermostat that you can easily replace with anything in the (160-195 °F) degree range.
Gabe
Reviewed in the United States on February 9, 2025
These seals take a little bit of tightening and you may need a little antifreeze or oil to seat the o-rings so they do not bind. However if you are doing a custom mod where you need the hose to face a different direction. This works great. I mounted my engine temp sensor as well and you will need yellow Teflon for that.Be advised you cannot use the oem thermostat with dual chambers. It is one thermostat for the whole car.
Andrew Stutz
Reviewed in the United States on January 17, 2025
Works very well. I didn't have any issues with leaks with just the included gasket. I did however find the thermostat that was including to only get temps up to 150F 66C. Included thermostat has 82C on it. I replaced the thermostat with a 77C one from a 2005 civic EX and now the engine gets up to proper temps. Good unit just change the thermostat
William
Reviewed in Canada on August 20, 2024
You can install it with or without the heater housing. It doesn't leak. Yiu can put different types of hoses. It comes with a working thermostat, and hardware! 5/5
dejanaye knox
Reviewed in the United States on March 6, 2024
The media could not be loaded.
Savannah Peterson
Reviewed in the United States on December 30, 2024
Looks nice but none of the plugs fit properly. I wrapped din teflon and even tried Honda bond but it still leaks. I returned the product .
Alexander
Reviewed in the United States on January 6, 2024
Installed on my all motor k24a build and works fine.
Louis
Reviewed in the United States on July 2, 2023
Ok guys I posted pics just in case someone wanted to get one it works great all u must do is high temp and oil resistant plummers tape all the block off ports to prevent leaks common sense tbh and u must switch out the thermostat with part # 7242-170 u can use the same gasket the thermostat comes with as well just need the the new thermostat and also a fan switch sensor for the other block off port since it doesn’t come with one part # tu197 . Or u can get it used from someone parting out a Honda works the same , again guys very happy with this part and looks dope.
Lambo7727
Reviewed in Canada on July 1, 2023
Still working after a year
Jorge Alfredo sosa Sandoval
Reviewed in Mexico on November 28, 2023
Excelente para el proyecto
maddy
Reviewed in Canada on April 7, 2023
Bought the itemSays it comes with all fittings to plug off holes not used.Did not come with any.Now I have to find another solution.
Jaxsdad
Reviewed in the United States on October 1, 2022
Great product fast shippping
Susan Fox
Reviewed in the United States on November 12, 2021
Fit my k24/k20 frankenstein build great and looks good aswell
Recommended Products