Your cart is empty.
Your cart is empty.Product Description
Driver Side Bottom Cloth Seat Cover + Foam Cushion Replacement for 2009-2012 Dodge Ram 1500 2500 3500 4500 5500 SLT Gray
Cloth Seat Cover
Seat cover is made of premium cloth for superior comfort, which is washable and easy to clean. It is not sensitive to temperature, so even if the car temperature is high in summer, the temperature of the car seat is not high. Actual replacement cover, not a slip on or pullover, you will remove the old cover & then Install the new cover.
Foam Cushion
Foam cushion is made of advanced foam material. Soft and non-deformed, can effectively protect the seat in the car. The seat cushion, which can evenly distribute body weight, disperse pressure and keep soft after long time use. Reinforced backing to prevent seat springs from sinking in & damaging your new foam cushion. Ergonomically designed seat cushion provides maximum support and comfort while reducing pressure on the coccyx/tailbone and promotes posture.
Replacement for
2009-2012 for Dodge Ram 1500 SLT, Longhorn, Sport, Power, Wagon, ST, TRX, TRX4, Tradesman, Outdoorsman.
2009-2012 for Dodge Ram 2500 SLT, Longhorn, Sport, Power, Wagon, ST, TRX, TRX4, Tradesman, Outdoorsman.
2009-2012 for Dodge Ram 3500 SLT, Longhorn, Sport, Power, Wagon, ST, TRX, TRX4, Tradesman, Outdoorsman.
2009-2012 for Dodge Ram 4500 SLT, Longhorn, Sport, Power, Wagon, ST, TRX, TRX4, Tradesman, Outdoorsman.
2009-2012 for Dodge Ram 5500 SLT, Longhorn, Sport, Power, Wagon, ST, TRX, TRX4, Tradesman, Outdoorsman.
Dan
Reviewed in the United States on February 27, 2025
They match the existing seats, but the one that I got isn't much better than sitting on some boards. The foam is way too stiff and very uncomfortable.
Sandra Duran
Reviewed in the United States on August 25, 2024
Not what was promised
Todd R.
Reviewed in the United States on May 21, 2024
The metal clips are a pain but as i was doing it , i thought that wire ties would way easier if you double them up . Quality is pretty close to factory but not quite .You have to make several holes but easy enough . So far 1 drive and only draw back is you have to break in a new seat . Came out great .
Ashley Boehner
Reviewed in Canada on March 11, 2024
I replaced my ripped drivers seat with this product, it looks great! Keep in mind you need to purchase hog nose pliers and hog rings to install this. Additionally, if your ram has electric buttons to move the seat forward/backward, etc - you will need to cut the fabric to make the controls fit.
Brett
Reviewed in Canada on December 5, 2024
Would prefer black stitching over white, but it fit perfect, the clip is a little loose on the seatbelt side, but beats my old crumbling seat.
Robertson
Reviewed in the United States on November 20, 2024
Fits perfect.easy to install once seat is removed.
Joseph Renteria
Reviewed in the United States on November 19, 2024
Fit great. Looks great. Easy install. Hardest part is hooking the rings to tie cover to cushion. 20 minutes and done.
Barry
Reviewed in Canada on November 17, 2024
Appear to be quality materials and foam.My 2012 Ram has a much lighter grey than this one which is black advertised as grey.
Evan
Reviewed in the United States on November 13, 2024
Installed in a 2012 Ram 1500 ST standard cab. Plan on removing the drivers seat for this replacement. In my truck, four bolts (18mm back, 15mm front) and three electrical connectors under the seat (disconnect the battery ground first, since one of those connectors is for the airbag in the seat back).Comes with a bag of hog rings. These are to secure the fabric seat cover to the foam padding; they are not for fastening the cushion to the seat frame.I used needle nose pliers to close the hog rings with not too much trouble (didn’t bother with hog ring pliers). Be sure to twist them so the pointed ends are facing the bottom of the seat.Disassembling the seat to remove the old cushion was a little tricky. The lever to recline the seat back is held in place with a clip just like a window crank. Once that is removed, the rest of the side panel is easy to remove with a trim tool.You will need to cut small slits in the bottom fabric to fit over the seat recliner stub and one screw hole.There are clips to attach the cushion and cover to the seat frame; front, back, and both sides. Make a note of what they are connected to when removing the old one.The entire job took maybe two hours. There was a noticeable but not significant increase in seat height with the new cushion. That will probably fade as the cushion is compressed and broken in.Good color match, comfortable, and there aren’t chunks of foam all over the floor any more.
Jennifer Welch
Reviewed in the United States on October 29, 2024
The seat is easy to install. Very comfortable.
Shawn
Reviewed in Canada on October 23, 2024
Put seat cover up to my old seat and the new seat cover sides are a darker gray. It’s very noticeable, maybe it well faded overtime to match the other seats.
Sam
Reviewed in Canada on October 14, 2024
The media could not be loaded.
John Dunn
Reviewed in the United States on July 16, 2023
Form and fit is pretty good…but how hard or expensive is it to use black or dark stitching. The rest of the seat is black stitching, the new piece has white stitches.
Recommended Products