Your cart is empty.
Your cart is empty.Keep the tools you need at your fingertips with the OEMTOOLS 22218 Rail Wrench Organizer. These wrench organizers for toolboxes and workshops are quick to assemble and are slotted in ascending order for easy identification. The rail tools’ versatile plastic construction allows experienced technicians to cut them to size to better utilize their space. The open, minimal wrench organizer rail design allows total visibility and access while you're on the job. Holding up to 35 individual tools, this non magnetic wrench organizer can be affixed where ever you'll need them most with a strong adhesive backing. Grab the right tool the first time, every time with OEMTOOLS 22218 Rail Wrench Organizer.
Customer
Reviewed in the United States on September 16, 2024
great gift for my teenage son when he was setting up his tool box. highly recommend.
Big daddy
Reviewed in the United States on February 13, 2024
The media could not be loaded.
Thomas
Reviewed in Canada on December 22, 2024
They work OK to hold wrenches, but they’re kind of expensive for what they actually are
Zach Harrison
Reviewed in the United States on December 18, 2024
I didn't expect them to fit the variety of wrenches that they do. Compact or set wider they saved half a drawer over traditional wedge shaped wrench racks. Probably will buy a couple more sets.
Michael C.
Reviewed in the United States on November 2, 2024
These give you the best bang for your buck in terms of spacing. Closest spacing I have found in 30 plus years.
Customer
Reviewed in the United States on January 10, 2024
Cut to size to fit in tool box. Worked but wouldn't brag about them.
Apprentice
Reviewed in Canada on January 1, 2024
Simple and good
cafe
Reviewed in the United States on March 11, 2023
Yes you can organize your wrenches takes up a lot of space in your box I wouldn't buy them again
Customer
Reviewed in Canada on March 26, 2022
Did a great job of organizing my wrenches and creating more space in the tool box.
Ashley Bauman
Reviewed in Canada on March 28, 2020
Ive tried them all. Great product. Deep tool box drawers are best.
Jeremy T
Reviewed in Canada on November 29, 2020
Awesome like these ones cause they don’t have the size change on the rail for smaller wrenches that you don’t need to have the change works awesome
Pete Rose
Reviewed in the United States on October 1, 2019
First thing to point out is there are reviews describing 2 different styles of wrench holders here. The two strips of green 35 wrench holders is a very low profile straight wrench holder. It allows pretty big wrenches to go into shallow drawers and is a great product. Then there are reviews for the space saver rails that allow you to organize wrenches that allow one set to go from large to small and the other set to go from small to large. This allows the wrenches to be installed in a “V” pattern. This requires one short rail to be placed vertically and the long rail to be placed on an angle. So each set requires one long and one short and the other side gets a short and long. They are numbered 1-4 showing how they get laid out. If these people leaving negative reviews can’t figure out how to properly set up a wrench organizer could you imagine them working on someone’s car? Scary to think people could be so stupid.
Nick
Reviewed in the United States on December 14, 2018
These do a great job of utiziling empty space (ie, the space in the drawer ABOVE flat-resting wrenches). When you have a tiny shop, you're looking to fill in whatever dead space you can. These solve one problem.While I have the full gamut of sizes in both SAE and Metric, these won't work going from tiny (6mm) to huge (40mm), but I found if you cut them exactly in half, they work great for 6mm to 22mm (standard set) in 6 point and then the same thing in 12 point.The same is true for SAE. Standard kits are 1/4" to 1". Cut them in half and you get a "free" set for your 6pt or 12pt.You even have a few slots left over on SAE and can fill them in with 1-1/16", 1-1/8" and 1-3/16".The largest sizes will rest on the wide head and tail of the wrench itself instead of the valleys of the divider, but still fit and look fine.
Recommended Products
