Shopping Cart

Your cart is empty.

Your cart is empty.

PATIKIL 50W 50 Ohm Aluminum Shell Resistor, 4 Pack Aluminum Housing Resistor Housed Case Wirewound Resistors Screw Tap Power Resistor, Golden

4.9 (3) Write Review
Free shipping on orders over $29.99

$12.95

$ 5 .99 $5.99

In Stock
  • Color: Golden; Material: Aluminum; Power: 50 Watt; Resistance: 50 Ω; Tolerance: 5%; Mounting Type: Chassis Mounted with Screws; Mounting Hole Diameter: 3.5mm / 0.14 inch;; Mounting Hole Distance: 40mm / 1.57 inch;; Rod Length: 180mm / 7.09 inch;; Total Size: 50 x 16 x 16mm / 1.97 x 0.63 x 0.63 inch(L*W*H); Packing List: 4 x Aluminum Housing Resistors
  • Advantage: The surface of the aluminum power resistor has cooling grooves, is small in size, has high-temperature resistance, and strong overload capacity, and can be used in harsh environments. The induction resistor has a solid structure and high stability for long service life.
  • Instruction: The aluminum-housed resistor is easy to install, and suitable for cooling plate installation. Connect the wires to the shafts on both sides, choose the appropriate size of the screw and install it on the hole.
  • Application: This aluminum load resistor is suitable for the lighting product, audio, Frequency converter, frequency divider, inverter, and other industrial control. Chassis-mounted resistors are widely used in power supply and automation equipment in the industry.
  • Note: The aluminum wire wound resistor will get hot when working, please do not touch it. Axial load resistor should be mounted on metal board, please do not install it on flammable board such as plastic board, rubber, paper, wood, etc.


Product Description

Aluminum Shell Resistor Aluminum Housing Resistor Housed Case Wirewound Resistors Screw Tap Power Resistor

1

Advantage

The surface of the aluminum power resistor has cooling grooves, is small in size, has high-temperature resistance, and strong overload capacity, and can be used in harsh environments. The induction resistor has a solid structure and high stability for long service life.

Instruction

The aluminum-housed resistor is easy to install, and suitable for cooling plate installation. Connect the wires to the shafts on both sides, choose the appropriate size of the screw and install it on the hole.

NOTE

  • The aluminum wire wound resistor will get hot when working, please do not touch it
  • Axial load resistor should be mounted on metal board, please do not install it on flammable board.

Harold
Reviewed in the United States on February 9, 2025
Bought these to bring a pair of 6ohm speakers to 8ohms so they could be run in parallel with another pair of speakers. Worked perfectly and the amp section of the AV receiver has the correct impedance now.
Yerlin
Reviewed in the United States on January 6, 2025
Muy mala calidad se calientan en segundos
Mr B
Reviewed in the United States on September 23, 2024
All available replacement speakers seem to be 4 ohm, Chevy ( in their infinite wisdom) used 8 ohm speakers in the rear doors, no where else, just the rear doors. My amp and complete system is factory and reading up told me using 4 ohm would work awesome, but probably fry the circuit incthe main unit. Most of you replace the head unit anyway, but I am pretty boring, using the factory radio and its features. Z71 2002 Chevy Suburban , same as a Tahoe, and the GMC versions. Anyway, I used ohm meter to test before and after. I added simple connectors to the resistors so it all was plug and play, there happened to be a mount point in the door for attaching this resistor to the door. So my point is, inline, on one of the twoxwores, this resistor turned a replacement 4 ohm speaker into an 8 ohm to match factory specs for a Chevy Suburban 2002. I am a professional tech, but this is an easy job. You can do this.