Your cart is empty.
Your cart is empty.
Using DC Power Supply only may DAMAGE the driver. Use battery instead.
This motor driver is suited for a brushed dc motor with the following specifications:
- Operating voltage from 7V to 35VDC
- Rated Current
- Peak Current
Features:
- Bi-directional control for dual brushed DC motor.
- Support motor voltage from 7V to 35VDC.
- Maximum current up to 80A peak (1 second), 30A continuous, each channel.
- On board MOSFETs are switched at 18 KHz for quiet operation.
- Regenerative Braking.
- On board Error LEDs to indicate: (each channel)
- Input Error (Blinks 2 times)
- Under Voltage Warning (Blinks 3 times)
- Over Voltage Protection (Blinks 4 times)
- Over Temperature Protection (Blinks 5 times)
- Thermal protection.
- Current limit protection.
- Multiple input modes:
- RC (Radio Control)
- Analog voltage from potentiometer/variable resistor/joystick
- PWM and DIR (sign-magnitude and locked-antiphase) from microcontroller
- Serial Simplified or Serial Packetized from microcontroller
- GROVE compatible connectors for control input.
- RC (Radio Control) friendly connectors.
- On board push buttons for fast test and manual operation.
- On board LED indicators for Error, RUN, Over current, motor output, for each channel.
- THIS MOTOR DRIVER DOES NOT HAVE A REVERSE POLARITY PROTECTION
- Dimension: 81.28mm(W) x 101.60mm (L) x 42mm (H)
Michael Ingersoll
Reviewed in the United States on July 23, 2024
This was so simple compared to using an arduino.... with a pwm motor driver with pots and rocker switches the route to pins-in and out. Literally ran my, rather large, 200lbs rc robot with my tx and rx connected.I did try and change the tx setting while it was live and it ran away.... but that was my rookie mistake.I would buy 3 more if they were a little cheaper. But WELL WORTH THE MONEY
Plasma
Reviewed in the United States on June 25, 2024
Are you wanting to modify an electric wheelchair to get rid of the stock joystick controller and make it radio controlled instead? Then yes, this is what you are looking for. It just works. You can plug your radio receiver straight into this, and be driving in less than 10 mins.Then when you're ready to upgrade it to a real robot by using microcontrollers, you can simply plug in your microcontroller into the serial input of this thing and start doing all kinds of fun stuff.Just buy this already :)
Customer
Reviewed in the United States on December 4, 2024
The media could not be loaded.
AJ Quick
Reviewed in the United States on November 20, 2024
Very nice motor controller. I had one issue that I'm unable to solve. The documentation makes reference to newer boards having different firmware and those boards being labeled with a green sticker. The version change is at v1.10. I see v1.3 referenced on the board.. however I don't know if that's higher or lower. Does it really mean v1.30? The only reason I would assume that is because the v1.10 update was several years ago and the likelihood of these being old stock seems unlikely.
MikeA
Reviewed in the United States on August 5, 2023
Very very nice but Slow Shipping
Fishman8880
Reviewed in the United States on March 9, 2023
I purchased this motor controller to replace a burnt Sabertooth controller that I was using for an R/C lawnmower build. The board is sturdy and seems well built. It stays much cooler than the Sabertooth but has less features. It's also about $40 less than a comparable Sabertooth. For my needs, this board is a great fit. Not much to mess with after installation, 2 channels (one for each motor if using for a similar project) can be used with tank style controls or mixed at the TX to get different configurations. It was very simple to do a basic R/C set up. Just connect to motors, power source, plug in RX, set DIPs and you're good. I'm certainly not an expert in this area, but in my opinion this is a very good mid / high amperage motor controller that is built to last.
Anthony F
Reviewed in the United States on October 17, 2023
Perfect application for my remote controlled lawn mower project. Programs easily to battery type used with it.
Recommended Products
$26.99
$ 13 .99 $13.99