Your cart is empty.
Your cart is empty.Optimize work spaces and increase opportunities for collaboration. Hang Quartet® aluminum-frame whiteboards and bulletin boards with ease. Adjustable hangers fit over cube walls measuring 1 1/2" to 3" thick. Two hangers per set.
Ray S. Lowe
Reviewed in the United States on September 5, 2022
Great for hanging whiteboard on a cubicle divider wall.
David J Putz
Reviewed in the United States on June 20, 2022
These work fine, but are a tad too small - wall is slightly thicker than 3". The metal is pliable enough to bend to work, which is a plus and a minus. They have worked well so far, though I've had to tape them down to the top of the wall so they don't come off. I think they would work well on a thinner wall, and weren't prohibitively expensive.
Hultins
Reviewed in the United States on December 9, 2021
Added to our newly arranged cubicle walls. Holding up well and able to use on wide variety of wall thickness
Sunshine Lover
Reviewed in the United States on August 14, 2019
I think these were great! I have a very large white board in my cubicle and these hold it up just fine. I noticed other reviews about the screw sizing being too small, but iIf you just press firmly the metal bracket into the black place holder it fits fine. It took me about 5 minutes to put them together and up and running.
mich
Reviewed in Canada on April 15, 2018
Great fit for its purpose. Less expensive than competitive products.
RobertC
Reviewed in the United States on August 21, 2017
Easy to install, but could be sturdier.
Roger B.
Reviewed in Canada on November 11, 2015
These hooks are made of very soft metal and I'm not sure how long they will last holding a white board!
InspectorGadget
Reviewed in the United States on January 4, 2014
These are very small and flimsy. They're adjustable to fit standard or thick cubicle walls. I used them to hang a big whiteboard (4' x 3') on the thinner style cubicle wall and they've been doing the job for a few months now without complaint. The board is a little floppy but that's a hazard of any kind of hanging system. I hardly notice it.Two caveats:(1) the little hooks on the end of the metal tongues fit under the metal rim of the whiteboard, but they'll tend to pull the rim off the board. I placed mine at the two extreme ends of the top of the whiteboard and they've worked well there, only pulling a little.(2) The internal screw that locks the plastic clip to the metal tongue sticks below the bottom surface when it's screwed down. You'd do well to cut off this excess with a file or hacksaw, or maybe one of those bolt-shears in the head of a crimping tool.The company should really supply screws that are the correct length. With the excess screw sticking out the bottom, the clip rides up at an angle and doesn't look secure where it hangs on the cubicle wall top. It still holds, though. Even with my big whiteboard (I still haven't trimmed my screws).
Donald G. Zellman Jr.
Reviewed in the United States on December 14, 2013
The hangars work great on my cubicle. They adjust well and are sturdy. For the price it's a good deal.
run2sea
Reviewed in the United States on December 27, 2006
The materials used are very low quality for the price of these hangers. The screws are so soft and short that 5 out of 8 became stripped as I removed them from the lightweight aluminum bracket (necessary to connect to the plastic portion) and were unable to be used. I took special care in unscrewing these after the first one became stripped, but the overall quality of the metal is really poor.The plastic and aluminum of the brackets are both flimsy and I would be concerned about using these brackets to support anything but the lightest of dry-erase boards. This is accentuated by the short fastening screws which (even when not stripped) probably are only holding the bracket together by a thread or two.I'm also unimpressed by customer service of this vendor. I asked them to send me 1 or more replacement screws, but they stated that won't do this since they don't stock spare parts. They then had the gall to advise me to contact the manufacturer. After spending over $32 on 4 brackets I expected a little more. I am requesting a full return and will post additional vendor feedback based on how this goes.
Recommended Products
