Your cart is empty.
Your cart is empty.Product Description
Nema24 3N.m Closed Loop Servo Motor & 2HSS60 Servo Driver CNC Kit
Package include:
- 1 x 24HSE3N-D25 Nema24 3N.m Closed Loop Servo motor 88mm 5A
- 1 x 2HSS60 Servo Driver
- 1 x 2M Extension Wire
- Pdf. user manual (If you have not received the user manual at Amazon Message Center from us,please message us)
Nema24 Closed loop servo motor 3N.m 88mm
Specific
- Size:60x60x88mm
- Current :5A
- Phase:2
- Step Angle(degrees):1.8 degree
- Lead wire:4pcs
- Holding Torque:3N.m
- Resistance:0.5±10%Ω
- Inductance:1.8±20%mH
- Insulation resistance:100MOhm(500V DC)
- Insulation Class:B
Features
1.2.1 Stepper motor closed loop system, never lose step.
1.2.2 Improve motor output torque and working speed.
1.2.3 Automatic current adjustment based on load, lower temperature rising.
1.2.4 Suitable for all mechanical load conditions (include low rigidity belt pulley and wheel), no need
to adjust gain parameter.
1.2.5 Motor work smoothly and low vibration, high dynamic performance at acceleration and
deceleration.
1.2.6 No vibration from high speed to zero speed
1.2.7 Drive nema 24 series 3N.m closed loop stepper motor.
1.2.8 Pulses response frequency can reach 200KHZ
1.2.9 16 kinds microsteps choice, highest 51200microsteps/rev.
1.2.10 Voltage range: DC24V~50V
1.2.11 Over-current, over-voltage and position ultra difference protection function
2HSS60 Servo Driver
- Voltage range: DC24-50V
- Peak current :Peak 6.0A
- Logic input current:7-20mA
- Frequency:0-200KHz
- Suitable motor:57HSE76-2N
- Encoder lines:1000
- Insulation resistance:>=500MΩ
- Operating temprature:0~50℃
- Operating humidit:40~90%RH
- Virbration:5.9m/s2Max
- 2HSS60 is 2 phase nema 24 series hybrid stepper servo driver. It adopts new generation 32 bit DSP
- and vector control technology, which can avoid the stepper motor losing steps and ensure the accuracy of the motor.
- The torque reducing is much lower than open loop stepper motor when it is at higher speed.
- The high speed performance and torque are enhanced in a great extent. Meanwhile the current control is based on the load, that can reduce the motor temperature rising effectively, then can extend the using life of the motor.
- The build-in place in position and alarm output signal can help the upper monitor to monitor and control. The function of position ultra difference alarm can ensure the machine work safely.
- The closed loop system is an ideal improvement and a good replacement of open loop system.
Attention:
- This 2m extension cable of this encoder must be connected during use.
Wiring diagram
Applications
- Closed loop stepper system can be applied to all kinds small automatic equipment and Instruments, such as engraving machine, special industrial sewing machine, stripping machine, marking machine, Dispensing machine, cutting machine, module phototypesetting, graph plotter, NC machine, automatic, assembly equipment and so on.
Loren Zimmerman
Reviewed in the United States on January 18, 2024
Works better than your average closed loop stepper motor!
Chuck
Reviewed in the United States on February 12, 2022
Works very well for my Lathe lead screw application.
Rodolfo
Reviewed in the United States on April 6, 2022
One item that immediately noticeable, I how quiet these things are at low speeds. And because they only use the current they need based on load, they also run very cool. I bought two of these for X and Y. After seen and hearing the difference, I’ll be buying the Z axis as well! I was also able to bump up the speed and acceleration on my machine. Win, win!
Timothy McCubbin
Reviewed in the United States on June 15, 2018
These motors worked great replacing regular steppers. Very smooth and powerful for the size. Everything worked out better than anticipated. Thank you!
Recommended Products