Your cart is empty.
Your cart is empty.Product Description
16 Channel Converter Receiver Signal Transverter
Sbus to PWM Converter
- SBUS to PWM/PPM decoder, 16 channel output, supporting the PC Settings.
- Note:not supported futaba7008 and the updated receiver, only support generation sbus(futaba6008 and before 6008) receiver
- Used to decode SBUS signal to PWM signal for conventional analog or digital servos with SBUS receivers.
- PWM Ports: conventional analog / digital servos
- SBUS Port for FrSky SBUS Servo Channel Changer.
- Any port output and any channel data ,can be more ports output 1 or more road signals
- If you have to use a lot of servos, will need it,suiltable for a CPPM 12 ch signal and 4 PWM signals (ch 13-ch16) from an SBUS 16 Source
- Channel: 16CH.
- Suitable for Futaba Orange Frsky.
- Any port output and any channel data ,can be more ports output 1 or more road signals.
- Customize all channel output sequence , SBUS decoder support decoding futaba/orange for Frsky SBUS signal.
- Allows you to repeat a signal to a tracker and extract flexibly pwm signals to move servos tracker.
- and on the other hand a SPPM chain to inject into a long-range control system.
Package :
- 1Pcs RC SBUS To PWM/PPM Decoder.
Poent
Reviewed in the United States on March 2, 2025
This is an elegant, low-cost solution for converting SBUS into 16 independent PWM channels, and it was easy to get working right away. I tested it with a couple different controllers and had no issues either time. The "casing" is just some thin plastic sheet and squishes easily, but I don't think it will be a problem or make it any less durable. pin-to-pin it's about 44mm long, and 27mm wide. I haven't noticed an appreciable difference in battery life with this running as well.
Arron Bates
Reviewed in the United States on August 5, 2024
My first gripe is that it assumes failsafe the moment it is turned on until it receives a signal, and the failsafe positions can't be changed. In giant scale RC, it is common to need to gang servos, and they will each have small differences from servo to servo, so the failsafe position means they will try and kill each other until the proper signal is received.I got around the failsafe problem, it was working in a giant scale aerobatic model, until recently. All of a sudden the ignition is pulsing, the aileron gangs aren't working properly rendering ailerons useless, and is causing excessive current draw. Remove this SBus expander and everything is fine, so something is seriously wrong with it.I am happy that I didn't lose the model the flight before, so it managed to get through that... but, certainly for large aerobatic models, I am going to use something else.
Garet Urban
Reviewed in the United States on April 3, 2024
The pins are opposite to what you are used to so watch that and it's a great little expansion board. My complaint would be the case it's just a plastic sleeve that's not attached at all so it's constantly wanting to fall out of the little protective sleeve making it kind of hard to put the connections together, other than that I think it does what it's supposed to do
J. Lester
Reviewed in the United States on May 18, 2023
So nice to now be able to convert an ELRS receiver to 16 channels !
Muthanna Alwahash
Reviewed in the United Arab Emirates on September 6, 2022
Worked perfectly with Frsky X8R expanding the SBUS signal to 16 Channels PWM. Marking of PC TX is not correct on the cover (reading RX on both sides). but it is correct on the inside PCB as shown in diagram for this product on Amazon.
Customer
Reviewed in the United States on June 8, 2022
I use to expand my X8R receiver to 16 channels.
Recommended Products
$26.99
$ 11 .99 $11.99
$349.99
$ 99 .00 $99.00