Your cart is empty.
Your cart is empty. Mount Size: 7/8in.
Handlebar Size: 7/8in. or 1-1/8in.
Rox new offset block Riser raises your bar straight up 1in. (vertical) or up 1in. and back 1in. when installed the other direction. Rox Pro-Offset risers have an oblong hole so that they will fit virtually any fore and aft bolt center to center distance with 8mm bolt threads acting as a fat-bar adaptor or they will work to raise your stock fatbars on BMWs (not 08-up Adventure), KTMs and more. Always check and confirm that your bike has adequate cable and brake line length before installing any handlebar risers.
Tom S
Reviewed in the United States on September 6, 2024
These risers were simple to install in about 15 minutes on my NC750x without any cable modification. Shipping was fast.
Frank
Reviewed in the United States on March 10, 2024
Worked perfect, bars are now above forks as should be, installed on 08 Honda 230l
Frank
Reviewed in the United States on December 16, 2024
After rerouting the clutch it brought the handlebars closer to me and made them higher. It’s now in a more neutral upright position. I was having a shoulder ache before and now it’s gone.
jerrod
Reviewed in the United States on December 15, 2021
These are an exact fit for my handlebars with the given inserts. They add a comfortable fit to your riding posture and reduce fatigue on a longer ride. Though these are not labeled as a form of vibration dampening, I feel like it has been reduced.
elingemd
Reviewed in Mexico on November 5, 2020
Excelente calidad, hecho 100% en USA cono lo indican observándose en sus acabados y materiales. Ideal para Suzuki Vstrom 650 XT 2018 ya que no requiere de cambiar ningún cable (frenos, acelerador, etc.). Mido 1,83mt y me dio la altura necesaria para estar de pie en Off Road y cómodo en carretera. 100% recomendable
Customer
Reviewed in the United States on August 5, 2019
These Rox risers are very well made from solid aluminum (not the cheap and brittle cast aluminum like some other brands). I love their unique 1" rise and 1" pull-back design. You can also install them reversed so they only rise 1" but don't pull back. I installed these on a 2015 Triumph Bonneville SE in the 1" up and 1" back configuration and they fit perfectly without needing to do anything to my cables. These Rox risers really make a big difference on how I engage with the handlebars and make my ride much more comfortable. Highly recommend.
Jim McCloud
Reviewed in the United States on June 10, 2019
I installed these on a 2019 KTM 500 and the fit was perfect. Really good quality units with a nice finish. I was able to keep the same routing without having to extend cables. I am 6’5” and I had to really lean over when standing up. It is perfect now without being too high. I have had bar risers on other bikes that were too tall and it made hill climbs harder as it put me to far up and back.
PublicCitizen
Reviewed in the United States on January 31, 2017
Installed on a 2012 RMZ450. I'm 6'2" with long arms and needed an offset riser. I was running a standard 30mm riser with my factory 1 piece top clamp with a stock bend handlebar. I bought these with intentions of removing my non offset 30mm risers and just using the bottom offsets attached to my factory lower bar mounts and then reuse my factory 1 piece top clamp. This riser is machined and finished nicely but the top clamp holes are not the same distance apart as my factory single piece top clamp. You do not want to install these risers on a dirt bike without a 1 piece top clamp or you will have bent and or twisted lower mount bolts where it attaches to your top triple clamp after a crash. I ended up machining my factory 1 piece top clamp ".020 elongated closer to the bar on each hole " to allow me to mount it with these risers. I never intended nor wanted to run them with the supplied dual piece top clamps and I'm glad it worked out with minimal fitment to my factory top clamp.I also added Fastway foot pegs installed in the lower position and a Turner Performance Products RM High/Carmichael bend handlebar to max out my cable length and the bike is so much easier to ride and less arm pump. The offset did not effect the bikes cornering ability in any negative ways in fact its the best its ever been and I'm not sure if its the geometry or just the fact that I'm that much more confident in this new rider position.
Customer
Reviewed in the United States on December 5, 2016
Very good quality, easy to install.
Recommended Products
$28.72
$ 12 .99 $12.99