Your cart is empty.
Your cart is empty. Why Choose Our 1400D+900D Jon Boat Cover?
RVMasking Upgraded High Quality Waterproof Jon Boat Cover features heavy-duty fabric for Max Weather Protection, Easy Installation, Custom Fitting and Extra Strength, including:
-1400D polyester Reinforced+ 900D polyester in end + 2 PU coating + anti-UV coating, repels water, anti-scratch and protects against dirt and sun damage
- 2-in-1 motor cover/storage bag
- Total double stitching seams
- Bar-tack stitches for all strap loops
- Strap loops design suitable for mooring
- Elasticized hem for a custom fit
- multi adjustable straps with plastic buckles
Please measure before purchase
- Measure the center line length:
Straight measurement from bow to stern,not includes the motor, make sure include tolerance for excessive bow rail heights, trolling motors, ladders, and transom platforms etc., DO NOT to measure up and over the windshield
- Measure the beam width:
Straight measurement for the widest distance across the boat, flat line from side to side at the widest point on the hull. Do NOT measure up and over the windshield
- Move up to the next size if your measurement falls on maximum length.
PACKAGE
1*Instruction manual
1*2-in-1 motor cover
1*boat cover
9*windproof straps
Ward Smith
Reviewed in the United States on March 8, 2025
So far a good cover for the price, made it through the winter without rotting like the last one I bought
Meem
Reviewed in the United States on March 20, 2025
Fit right, easy to put on and held up to the weather.
Tony Collins
Reviewed in the United States on February 18, 2025
We will see how well it holds up but so far seems great
Customer
Reviewed in the United States on February 14, 2025
I like it. Sturdy. Well made. Good price. I'm pleased.
Jack W.
Reviewed in the United States on December 7, 2024
It's suits my purpose well. I haven't traveled with it yet but I don't think that will be a problem. It keeps leaves and water out as advertised.
Amy Maddocks
Reviewed in the United States on December 17, 2024
This is a nice boat cover. It's thick & made of a durable material.We have 2 boats that stay in our backyard when not being used. The latest 1 is covered & protected, but our Jon boat wasn't. It is directly under 2 trees as well. We had 2 hurricanes come through Tampa Bay this season & afterwards the leaves, limps & water in the boat was ridiculous. We have foam in the bottom of our flat bottom with a PVC plastic sheeting over that to created a higher boat bottom. The foam helps the boat sit higher in the water, but leaves can get stuck around the edges & ends up clogging the drain hole. We needed it covered to prevent all those issues.Our Jon boat is 12ft long & just over 3ft wide.This cover is made to fit up to 14' so it was a bit long for our boat, but I could hook the front over the trailer bar instead, pulling it tight When I opened it up the 1st time, it did stick to itself some. It's just that type of material. Once I had it all unfolded it was easy to maneuver it around the boat. For reference I opened it over the boat so I didn't have to transport a big cover from the ground up onto the boat. The front is labeled.The elastic around the entire outside is thick & helps keep the cover in place. Because our boat is only 3ft wide, it pulled down a good amount over the sides.The canvas straps are a good size, the clips don't feel cheap & they clip onto & off of each other easily.All the spots the straps loop through are reinforced with extra material. That is great. There is so much pressure on that area that it's usually the 1st to rip & tear. On this cover though, there is double stitching through basically 3 layers so it's able to take the pressure.I pulled a strap through each loop around the boat, then because our boat is smaller, instead of clipping under the boat, I clipped under the trailer. This let me pull the cover tighter. I also could easily adjust the straps after I connected them so that I could reach the clips for every strap to quickly & easily remove the cover without having to reach down under the boat or crawl under the trailer to unclip.On the front loop, I added a strap & tightened it around the front of the trailer base. If your boat is 14ft, you won't need to do this.My only issue with this cover is that I wish there were 2 more loops. If there were one more loop on each side, in between the 1st & 2nd loops going down the front, I could pull it much tighter. Right now, I think no matter how tight I make it, water is going to pool in that front area. I'm going to put something under the cover to hold the area up & avoid that.If you need a jon boat cover I think this is a well priced quality option. I expect it to hold up well & do a great job protecting our boat.
Kyle Minton
Reviewed in the United States on December 12, 2024
It fits a 1649 monark jon boat with 2 seats and a lightbar with a little room to spare. The straps/buckles are a pain and you can't pull it very tight
Lonnie
Reviewed in the United States on November 20, 2024
Fit well, the vents are a nice addition!
Recommended Products
