Your cart is empty.
Your cart is empty.Bulkhead Fitting - 3/8"
Robert L.
Reviewed in Canada on July 13, 2024
Will bye more
Burona
Reviewed in Canada on October 27, 2023
My son vented his fuel tank to the air filter housing of his Ford Superduty and was unsure how to tap-in to the air box using 3/8 hose.. This barbed bulkhead fitting from Amazon was the perfect answer at a great price.
Team Curly Butt
Reviewed in the United States on February 13, 2022
Used this to pass the fuel line through the trunk of my car for a fuel cell install, while hooking the fuel cell to the stock lines under the car.Worked great and looks safe.
William N.
Reviewed in Canada on October 15, 2021
Perfect
Billy Bill
Reviewed in the United States on September 8, 2019
The overall quality is great and it will suite my purpose perfectly. However, this could use some sort of seal instead of just a metal washer.
John P. Kiffmeyer
Reviewed in the United States on June 8, 2019
This did what I wanted it to, but the fitting's shape and the included washer aren't a good fit. The washer fits around the shank of the fitting, but only the points of the hex profile catch the ID of the washer. I was afraid to torque it down to get a gasket to seal around the wall this was going through because the hex profile was likely to broach out the flimsy washer. I picked up another thicker washer to make it work. The fitting really needs a flange below the hex to press on whatever washer/gasket you put between it and the wall it's going through.
Shawn W. Durrance
Reviewed in the United States on June 22, 2019
Worked perfectly
Harold Greeno
Reviewed in the United States on May 23, 2019
I got tired of spilling gas when filling my lawn mower.So I came up with this idea, I bought the fowling items from Amazon, Ace Hardware, and Lowe's.3/8" Brass Bulk Head5/8"ID washerTap Cock Switch5/8" ID X 2" OD X 1/8" thick Rubber washer1/16"x 12" x 36" thick cork gasket material.Oil Resident Gasket dope in a tube.3 Radiator ClampsLoctite Vinyl, Fabric & Plastic Glue1/2" Drill Bit5/8" Drill Bit1/2" Tubing x 2" long3/8" Tubing x 6" longI drilled a 5/8 hole in gas can, and attached 3/8" Brass Bulk Head using cork and Gasket Sealer on both sides and tighten lightly.Take the 1/2" X 24" long Tubing coming form Gas Can Bulk Head with Radiator Clamp to Cock Switch with threads with Radiator Clamp3/8" 6" long Tubing coming small end of Cock Switch with Radiator Clamp, then going through Gas cap suing a 1/2" Drill Bit and Loctite Vinyl, Fabric & Plastic Glue. shove 3/8" x 6" tubing through lid and glue both sides. leaving 4" under cap to fill your Lawn Mower.
Mike
Reviewed in Canada on February 28, 2019
works well
gj
Reviewed in the United States on July 12, 2018
Did not need or use, but item would have been perfect. Really heavy duty.
Barry
Reviewed in Canada on April 23, 2018
works as it should
Christopher Purvis
Reviewed in the United States on April 5, 2016
I ordered the wrong size but it is a good quality item that I am keeping around because I will need it sooner or later. It's a nice fitting.
Paul A. Baldassarre
Reviewed in the United States on April 26, 2016
I used two of these to run fuel to and from a cab mounted fuel tank for an EFI install into an old Ford pickup. Much cleaner install that eliminated the need for rubber grommets.
Recommended Products
$13.53
$ 7 .99 $7.99