Shopping Cart

Your cart is empty.

Your cart is empty.

Self-Adhesive DIY Keel Guard for Fiberglass and Specific Aluminum Boats - Boat Keel Protector Hull Guard Protects from Rocks Ramps and Oyster Beds 5 Inches Wide 9.6 Feet Length

Free shipping on orders over $29.99

$59.99

$ 26 .99 $26.99

In Stock
  • Boat Keel Protector - Protect your boat keel from rocks, oyster beds, sand, concrete ramps and docks, abrasive wear and tear under water, saves the keel from constant abrasions, scratches and scars. Save the keel from any future possible damage with our keel guards and save the cost of boat repairing form continuous shore landing.
  • Boat Compatibility - Compatible with fiberglass and some aluminum boats. Keel guard for Recreational watercraft (Ski Boats, Skiffs, Dinghy and most Jet Boats), fiberglass boats (Bass Boats, Ranger Bass Boat, Ski Boats, Wake Boats, Runabouts), Some aluminum boats (Fishing and Jon Boats).
  • Premium Workmanship - The keel protector for boats is produced from thick and durable rubber that absorb the shocks and impacts with maximum protection on your boat keel. The rugged and flexible 5 inch wide boat hull protector conforms to your boat's keel easily and won't drag your boat down.
  • Superior Craftsmanship - The keel guard using strong 3M adhesives for maximum adhesion to boat, the tough yet soft 5-inch wide boat keel protection conforms to your boat's keel easily and firmly, and the drag reduction channels that won't slow your boat down. 9.6 Feet Length.
  • Easy to Install - The boat keel protector features an self-sealing contoured edge that creates a tight seal for long lasting protection. Only take 5 steps without sealants needed: delimit, etch, clean, prime, apply. Warm tips: keel primer was not included in the kit.


Boat Keel Protector - Protect your boat keel from rocks, oyster beds, sand, concrete ramps and docks, abrasive wear and tear under water, saves the keel from constant abrasions, scratches and scars. Save the keel from any future possible damage with our keel guards and save the cost of boat repairing form continuous shore landing.
Boat Compatibility - Compatible with fiberglass and some aluminum boats. Keel guard for Recreational watercraft (Ski Boats, Skiffs, Dinghy and most Jet Boats), fiberglass boats (Bass Boats, Ranger Bass Boat, Ski Boats, Wake Boats, Runabouts), Some aluminum boats (Fishing and Jon Boats).
Premium Workmanship - The keel protector for boats is produced from thick and durable rubber that absorb the shocks and impacts with maximum protection on your boat keel. The rugged and flexible 5 inch wide boat hull protector conforms to your boat's keel easily and won't drag your boat down. 9.6 Feet Length.
Superior Craftsmanship - The keel guard using strong 3M adhesives for maximum adhesion to boat, the tough yet soft 5-inch wide boat keel protection conforms to your boat's keel easily and firmly, and the drag reduction channels that won't slow your boat down.
Easy to Install - The boat keel protector features an self-sealing contoured edge that creates a tight seal for long lasting protection. Only take 5 steps without sealants needed: delimit, etch, clean, prime, apply. Warm tips: keel primer was not included in the kit.


Tina Correa
Reviewed in the United States on March 2, 2025
Red film was very tough to get off and it started to unstick from the boat after 1 day. Surface was prepped correctly. Protects the keel though I guess
Go KP
Reviewed in the United States on March 11, 2025
Don’t buy, it’s impossible to get the red plastic off of the adhesive. Waste of money
Jess Lovely
Reviewed in the United States on February 10, 2025
I got this for my powerboat. The forward portion of the keel has kissed rocks and beaches over the years and had a few dings. I got this guard to protect it. I cleaned the area well with xylene – could have used any other cleaning solvent, including rubbing alcohol. Once ready, I peeled off the first foot or 2 of the keel strip’s backing, exposing the adhesive layer, and placed it where I want it, then peeled some more and kept going until the full length was stuck down. Then I went over it again, tapping it firmly down with a rubber mallet, then ran a rubber roller over that. I gave it several days to really harden up and cure before I put the boat in the water. So far it’s stuck firmly, a good thing in water, with all the stress and abuse a keel guard must take.
Kayla Tortorella
Reviewed in the United States on February 10, 2025
I regularly use a concrete boat ramp that has no dock so I have to ground the bow in the ramp. My keel was taking a beating but those days are over. It took some time to do the proper prep but I wanted to do it right so the guard would last. I am very happy with this keel guard. The adhesive seems super strong so I expect a long life. The keel guard doesn't show any wear yet after multiple grounding on the ramp since I installed it. (Note: Need to buy extra tools to clean the bottom of the boat, good price compared to other products)
Dewayne
Reviewed in the United States on December 17, 2024
One of my favorite fishing spots has a ramp without dock so I have to pull my boat up on the ramp. Over time I've really abused the keel and had to fix it. I was leery of a keel guard. I was afraid messing up the install, and once its on, there is no moving it. I was also concerned about it staying on. Glad I was wrong on both accounts. If you follow the instructions / video just exactly as it says, it will work. I was surprised, it was really not a bad job. The best part is...it works. I've hit the ramp now several times and been in the water long enough to see that it's not coming off and that the ramp is not going to tear this thing up. If you have a favorite spot where you have to use the ramp...this is the answer.