Your cart is empty.
Your cart is empty. New 4 - 8 Way 5V LED Illuminated Joystick
Microswitch reliability tested to 20 million cycles
Rated voltage: + 5V (± 0.5)
The Octagonal Limiter has 8 "corners" for easier 8 way control.
The Circular Limiter is easy to rotate.
Including:
1x LED joystick
1x 5pin cable
1x 2pin cable for LED
1x Octagonal Limiter
1x Circular Limiter
Chris
Reviewed in the United States on April 2, 2025
The joystick itself is plug-and-play with my existing board, which was great. However, the LED did not work out of the box. After troubleshooting, I found that the red and yellow wires were flipped between the two ends of the connector. Once I corrected that, the LED functioned properly.Another issue is the connector on the joystick end—there’s a large solder joint that makes it difficult to plug in and remove. You have to force it in and out, which can be frustrating during installation.Overall, the joystick works, but if you’re planning to use the LED, check your wiring first, and be mindful of the tight connector. Hope this helps others avoid some frustration!
de oliveira helder
Reviewed in France on February 17, 2023
Attention éclair très peu !!!
Carlos Iván
Reviewed in Mexico on July 28, 2022
El producto cumple su función bien, solo que no funciona el LED.
jorge eduardo castro
Reviewed in the United States on July 13, 2022
As far as I’m concerned the joystick-led is functional and execellent, this device turned out much better than sanwa stick, Today my arcade stick works perfectly with SJ@JX, happy with the actual performance
Patient Gamer
Reviewed in the United States on April 21, 2022
Bought two. Strong switches, neither LED works. EDIT: The LEDs are miswired, negative for positive. The port for the led is packed under the housing, with a large solder lead that you have to jam the cable through. Terrible, terrible design. Light transmission tube is detachable, which is a bad and good (good to clean/adjust, bad for light transmission, but the lights don't work anyway) EDIT: Shaft is loaded with axle grease, will be unusable in 3 months due to to dust. Bought a competitor's version, it has a much bigger top ball, but much shorter shaft requiring extensions which makes the light tube too small. ffs. I cut the tube from this one to fit the better joystick, took the light cable and threw the rest in the trash..
Samuel
Reviewed in Canada on April 14, 2022
The joystick works fine but the led didn’t work for some reason
Virginia A.
Reviewed in Mexico on December 14, 2021
Es fácil de instalar el único detalle que solo sirve para reemplazar la palanca ya que el conector y los microswitch no son compatibles para usarlo en la consola PS4 tendrías que poner los que viene de fabrica en el qmba drone. En cuanto la palanca se siente fluida para los movimientos en juegos como the King of fighters. Lo recomiendo para reemplazar la palanca
Juan m Ramos
Reviewed in the United States on January 5, 2021
joystick led does not bright that much
Eric Gooch
Reviewed in the United States on April 3, 2021
Arrived much sooner than expected or the dates seller posted. My only issue was the microswitch board used different pin connecters then what was on this board and the provided wire was long enough to reach the encoder for the player one side in my arcade but not the player two side. I just had to take apart the two joysticks and do my own frankenstein surgery taking the microswitch board from my old joysticks and implanting them onto these joysticks. Also, these led joysticks never are as bright as they look in the pictures, but they still light up nicely. I still gave 5 stars because it was my own fault for not checking if the wire connectors were compatible or not and other than that, these are great joysticks.
Recommended Products
