Your cart is empty.
Your cart is empty. This bipolar Nema 23 stepper motor is most popular, it with 1.8 deg. step angle (200 steps/revolution).
Each phase draws 2.8A, allowing for a holding torque of 1.9Nm(269oz.in).
Electrical Specification:
* Manufacturer Part Number: 23HS30-2804S
* Motor Type: Bipolar Stepper
* Step Angle: 1.8 deg.
* Holding Torque: 1.9Nm(269oz.in)
* Rated Current/phase: 2.8A
* Phase Resistance: 1.13ohms
* Inductance: 5.4mH+/-20%(1KHz)
Physical Specification:
* Frame Size: 57 x 57mm
* Body Length: 76mm
* Shaft Diameter: 6.35mm
* Shaft Length: 21mm
* D-cut Length: 15mm
* Number of Leads: 4
* Lead Length: 500mm
* Weight: 1.2kg
Connection:
Black(A+), Green(A-), Red(B+), Blue(B-)
Warning:
Make sure the motor connect to a constant current or chopper drive controller before you test motor.
Connecting the motor directly to a power supply will destroy the motor.
Rick
Reviewed in Canada on July 10, 2024
This motor has lots of torque and it's also very accurate.
Kent Lindquist
Reviewed in Sweden on November 5, 2024
enligt beskrivning
simone
Reviewed in Italy on November 23, 2024
Sono motori standard, ben costruiti, funzionamento impeccabile, prezzo nella media
daniel
Reviewed in France on January 22, 2024
Très bon produit reçu en parfait état , bon emballage correspond à mes attentes. Le délai de livraison a bien été respecté.
Randall Schultz
Reviewed in the United States on May 21, 2023
This is a nice strong little motor. Using it for a coil winder project, and this was perfect!
Flieppie
Reviewed in Belgium on November 28, 2023
Zoals verwacht
Scott Hart
Reviewed in the United States on April 1, 2023
First motor I got ended up being too big. I got this one and it fit and works great. Has plenty of power to move the spindle on the CNC machine with no issues
Randy Wisnia
Reviewed in the United States on July 7, 2022
I love my Shark HD5 CNC (HD510) but before I buy a 4th axis, which I would build or buy a generic one since NW is way over priced, I wanted to make sure I had good control over the 4th axis card I added and could find and jog what I believe to be the right motor. This worked. Searching posts I found enough info to select this one and wire a DB9 to the flying leads. This motor worked great as a test unit and I will now buy my 4th axis from Amazon. I can throw this motor into my spare parts bin or retrofit the lathe I like to accept this motor if the one that comes with is not quite right for my driver card. You assume all risk if you go this route but once you understand the important specifications you need, this would be a good way to test things out. There is some info I can't find on the Shark so I will have to experiment with things like gear ratio, and if have to either change the position of the physical motor or change it in software, but this helped with the learning curve.
Jim
Reviewed in the United States on October 24, 2022
I figured that quality of these would come down to customer service. HOWEVER! - Quality of packaging is just as impressive as the motor itself. Machined surfaces are bright and great surface finish, edges are perfectly chamfered. I doubt I'll ever even find out how good their customer service is. A++
corridor5
Reviewed in the United States on August 28, 2021
I didn’t want multiple steppers for my z-axis as they can get out of sync. My platform is fairly heavy (large and tightened to eliminate backlash). This stepper combined with StepperOnline’s DM542T driver, provides speed, consistency, high torque, and excellent precision. Very happy with the system.
John V.
Reviewed in the United States on July 15, 2018
These are great motors and they are very strong. I purchased 7 of these and I use them to build a prototype where these motors have to pivot an assembly by 87 degrees. They are quiet and while I had to write code to start them at low speed and increase the speed as they are moving, and also need them to release their hold every time a move is complete, they are always precise and don't miss a step. I use the to drive them and I feed it with a 24 Volt power supply. At this voltage, they pull about 1/2 an amp when holding. However, I should mention that one of them has pinched wires close to the motor but I take it this was a shipping issue and don't think I should reduce any stars for it.Also note that there is usefull information in a PDF described as "User Manual" under the heading "Technical Specification" on the If the power they offer is enough for your application, these are definetely recommended for whatever you are going to do with them.
Jordan Bartlebaugh
Reviewed in the United States on November 7, 2016
I love these motors. I currently have 4 of them and I have had them for about six months. They work great for what i was using them for and never seemed to have a problem. Just make sure you buy the right motor driver and power supply that will actually allow enough current through to power these motors. I was using drivers that had too low current output that kept it from using its full torque capability so it kept skipping steps. I have now fixed that problem and they work like a charm.Pros:smoothvery accurate stepsno need for radial encoder with proper set up and usageCons:noneI recommend this motor to anybody that needs a strong motor for either a project or in need of some type of upgrade.
walt
Reviewed in the United States on April 23, 2015
good strong motors
Recommended Products
$56.89
$ 28 .99 $28.99