No glare. Wasn't too hard to install. Can't even tell it's there on the screen. Super easy to clean.

A screen protector on a laptop that doesn’t have touch capability is considered unnecessary but knowing me, I needed it.It was an easy install and definitely protects my screen when closed or open. I added also because I have the keyboard protector.

Excelente material, muy buen material. Nos encanto la fácil instalación del producto, ya llevo 1 año con ella y no se despega ni se genera burbujas. Muy lindo y protege muy bien mi computadora.

This product came on time and in good condition. Nothing was bent or torn. This comes with 3 screen protectors, a card (that I assume you would use like a credit card or something hard to push on the screen protector when applying it on), and a cloth wipe.Originally, I wasn't going to buy a screen protector for my MacBook since I didn't used one for my previous HP laptop. But I figured I didn't want to risk scratching the screen of my expensive laptop, I decided I'll give this a try and I think it's pretty good so far. At first I was looking for a tempered glass screen protector, but those are rather expensive for the quantity that it comes in. This was the next best thing. I knew I didn't want a matte screen protector, since I have one on my iPad and I feel like it diminishes the screen quality a little bit. Again, THIS IS NOT TEMPERED GLASS, so DO NOT get this if you are looking for a tempered glass screen protector - this is a flexible, glossy screen protector.💻 MY LAPTOP: 13" MacBook Air M1 (2020)⭐️ HOW TO APPLY SCREEN PROTECTOR ⭐️1. Put your screen to sleep and on do not disturb, or turn off the laptop completely.2. Wipe your screen with an alcohol wipe. Use a piece of tape to get rid of any small piece of dust still left.3. Align the screen protector on the screen to the best of your ability, DO NOT PEEL OFF ANYTHING YET. Make sure you laid the screen protector down correctly - look at the sticker tabs on the screen protector to make sure.4. Tear off a piece of tape and put the tape half on the left (should be the side that also has the sticker tabs on the screen protector) edge of the screen and half on the screen protector. Tear off another piece of tape and put another one next to the first piece of tape, leave some room in between. It should look like you can lift the screen protector up and it would still be attached to the screen via the pieces of tapes.5. Start slowly peeling the sticker tab labeled '1' (this should be on the underside of the screen protector, if you had laid the screen protector on the screen surface correctly in step 3). As you peel, begin sticking the screen protector onto the screen, scraping out air bubbles with either your hand or the card that came in the package.6. Continue peeling until the whole screen protector has been stuck onto the screen.7. You can now peel the sticker tab '2' and this should take off the pieces of tape as well. And that's it. Congrats, you just applied your screen protector on successfully!! 🤩I did not have any trouble applying the screen protector using the steps above. **NOTE: The dust on the screen in the photos are on the outside, not the inside.** However, if you do have trouble there are 2 more in the package. After using the product for a few days, I don't think the screen quality has diminished or anything. I feel a little more at ease with the screen protector on my MacBook, though, which is good. I can still close my laptop properly as well. Again, this is a GLOSSY screen protector so it will NOT give you the anti-glare effect.Overall, I recommend this product. The price is decent for the amount you get, and the quality is not bad either. ⭐️⭐️⭐️⭐️⭐️

I'm writing this review just after installing on my macbook pro. I was skeptical, as always with a cheaper "off brand" screen protector. I figured it's $10 bucks, so can't go wrong. The install was sketch on a large screen. I have done multiple phones of mine in the past, but never did anything this large with 0 room for error.The install is easy to mess up, but not due to the product being faulty. The screen Realestate is just a lot to deal with, so you have to do your best to line it up perfectly. The protector is like 99.8% the same size of the screen, which is amazing, but leaves little room for error.I followed the video they have on their website on youtube and:1. peeled #1 tab layer about 30%2. quickly lined up the top left corner ( I used the rubber between the actual screen & the aluminum frame, "it's black".)3. let the screen adhere it self WITHOUT PRESSING OR TOUCHING THE SCREEN WHILE PEELING THE #1 layer off as it adhered.4. made sure the camera hole lined up before going past the 50 % mark.5. I peeled the #1 off completely and let the protector adhere.6. used the provided cardboard squeegee and took the very few bubbles I had out (maybe 4).7. DONE, LOOKS OEM, SUPER STOKED. ONE OF THE CHEAPEST, BEST PROTECTORS I HAVE EVER SEEN.For anyone that has had an issue, it's probably user error or a faulty protector/bad batch. I'm sure if you call them they will hook it up no problem.100% thankspeace!

Didnt come