Shopping Cart

Your cart is empty.

Your cart is empty.

Table Inserts (Pack of 3) for 14' Band saws or Scroll saws,Diameter: 2.5 in, Thickness: 0.1 in.(Please make sure this is your size)

Free shipping on orders over $29.99

$13.48

$ 6 .99 $6.99

In Stock

About this item

  • Three inserts to protect your expensive blades Please measure your saw as some Delta & Rockwell &Grizzly14" bandsaws has slightly smaller holes for the throat plate. If so some slight filing or sanding may be required.If you mind, please don't buy it.
  • use on 14" Band Saws and 24" Scroll Saws.
  • 2&1/2" X .100 thick Please measure your saws recess to ensure proper fit They fit Delta, Rockwell, some Jet, Ridgid, Grizzly, and other imports.
  • Make sure your insert recess has the locating pin on the side, not on the rear
  • IMPORTANT INSTALLATION NOTE:I have sold several hundred of these and occasionally someone will have the problem of it being a bit too large. First make sure the lip of the hole is free from dirt. If a table alignment pin,is not tight or missing,often the blade mounting slot will close up some over time which reduces the insert hole diameter slightly. I tap a flat head screw driver into the blade installation slot a bit to wedge it open. That should spread the insert hole enough for it to fit



Product Description

Product Description:

11

Describe:

  • Table Inserts (pack of 3).
  • Material: Aluminum
  • Make sure your insert recess has the locating pin on the side, not on the rear.
  • use on 14" Band Saws and 24" Scroll Saws.2&1/2" X 100 thick Please measure your saws recess to ensure proper fit. They fit Delta, Rockwell, some Jet, Ridgid, Grizzly, and other imports.
  • Three inserts to protect your expensive blades

插片

Attention:

  • Please measure your saw as some Delta & Rockwell &Grizzly14" bandsaws has slightly smaller holes for the throat plate. If so some slight filing or sanding may be required.If you mind, please don't buy it.

12

IMPORTANT INSTALLATION NOTE:

I have sold several hundred of these and occasionally someone will have the problem of it being a bit too large. First make sure the lip of the hole is free from dirt. If a table alignment pin,is not tight or missing,often the blade mounting slot will close up some over time which reduces the insert hole diameter slightly. I tap a flat head screw driver into the blade installation slot a bit to wedge it


David Buckbee
Reviewed in the United States on February 22, 2025
May need to sand down perimeter. About 1/16" to big for Porter Cable
Garwood
Reviewed in the United States on February 17, 2025
Bought these as replacements on my Delta 14" bandsaw. As many others have noted, they tend to be too large (and thick) to fit snugly in the recess. However, I found that by using my stationary sander and rotating the edge of the insert on the sanding surface while it was running, it took no time to trim off the excess material. I also ran the underside edge over the sander and had a perfect fit in less than 5 minutes. The new insert is even better quality than the original. The package of three should last me three lifetimes, but I would order these again if ever needed.
P Tipton
Reviewed in the United States on February 13, 2025
Thee do not fit a Delta band saw without work. They measure 2.270". The Delta Cutout is 2.250". Must have means of grinding these down to fit or you must use a lathe to trim them down.
Rick McMillen Sr.
Reviewed in the United States on September 25, 2024
Great price
Terry Noe
Reviewed in the United States on September 17, 2024
I had to grind down a little but then it fit good and works.
Hugh Bruce Parks
Reviewed in Canada on December 9, 2024
I've bought table inserts before, love these ones, better price, and they are excellent.
Smalley
Reviewed in the United States on July 20, 2023
The parts are slightly oversized in diameter (about 15 - 25 mils), but as advertised a little sanding (2 - 3 minutes) brings a perfect fit. Thanks.
Bob Ramsey
Reviewed in the United States on November 6, 2023
These are precision made ... but ... then they add the paint.The paint makes them too big around and too thick. I had to remove the paint along the edge with my grinder and wire wheel. It's a SNUG fit.Once in place, I notice that the plate is a little too thick and makes the plate stick up slightly higher than the saw tabletop.Again ... back to the wire wheel to remove the paint along the bottom edge, so it would fit lower in the hole and not stick up.Now, to their defense ... not every brand will have the EXACT same size. The slight over-size in this table insert might be a good thing.It took me 15 minutes to make it fit my bandsaw. It's a SNUG fit. Snug is good!
garry sooley
Reviewed in Canada on March 19, 2022
Got my Ridget 14 inches bandsaw table insert.
Steve
Reviewed in the United States on October 8, 2020
Gauge is good; finish is good, but these are TOO BIG for my 2& 1/2" insert slot on my table. That is, They're made too big. They're not big by much, but as anyone operating a band saw knows, "not by much" matters a lot. maybe it was cut to 2 & 1/2, and the growth happened during the finish process, which is akin to Engineers designing a library but forgetting to account for the weight of the books.Since only one of my 3-pack was shrink wrapped, I suspect that two other people found the same thing. Unwilling to work to sand these down based on the price I paid, I will also be sending these back.Junk.