- Home
-
All Categories
- Automotive
- Camera & Photo Products
- Arts, Crafts & Sewing
- Patio, Lawn & Garden
- Toys & Games
- Kitchen & Dining
- Industrial & Scientific
- Home & Kitchen
- Clothing, Shoes & Jewelry
- Tools & Home Improvement
- Electronics
- Sports & Outdoors
- Office Products
- Musical Instruments
- Video Games
- Computers & Accessories
- Pet Supplies
- Sports Collectibles
- Appliances
- Grocery & Gourmet Food
- Health & Household
- Baby
- Cell Phones & Accessories
- Beauty & Personal Care
- Software
- Payment
- About Us
- FAQ
- Privacy Notice
- Shipping & Returns
- Contact Us
Your cart is empty.
Your cart is empty.- Home /
- Automotive /
- Replacement Parts
- Cables
- Engine Cooling & Climate Control
- Engines & Engine Parts
- Steering System
- Shocks, Struts & Suspension
- Belts, Hoses & Pulleys
- Transmission & Drive Train
- Bearings & Seals
- Switches & Relays
- Body & Trim
- Windshield Wipers & Parts
- Sensors
- Fuel System
- Exhaust & Emissions
- Batteries & Accessories
- Gaskets
- Ignition Parts
- Starters & Alternators
- Brake System
- Lighting & Electrical
- Filters
- Motors
- Window Regulators & Motors
- Caps
/
- Sensors
- Transmission Speed
- Detonation
- Transmission Oil Pressure
- Map
- Camshaft Position
- Barometric Pressure
- Coolant Level
- Crankshaft Position
- Exhaust Gas
- Egr Valve Position
- Oil Level
- Fuel Injection
- Throttle Position
- Air Charge Temperature
- Mass Air Flow
- Manifold Temperature
- Coolant Temperature
- Ambient Air Temperature
- Oxygen
- Fuel Tank Valve
- Washer & Wiper
- Acceleration Sensors
- Timing Vacuum
- Manifold Differential Pressure
- Engine Temperature
- Courtesy Lamp
- Blower & Heater Fan
- Turbo Pressure
- Emergency Warning
- Cooling Fan
/
- Throttle Position
Product Description

ππππππππ ππππ πππππππ πππππ

πππ πππ ππππ ππππππ:

πππππππ πππππππ πππππππ ππππππ:
TPS APPS Throttle Pedal Position Sensor 2000 Dodge 3500 Cummins Dodge Diesel Pickups. FIT NOTE: If you have 2004. Please check to make sure the apps are mounted to the accelerator pedal. This is only for that fitment. This accelerator pedal position sensor replacement 100% new and best quality TPS manufactured can be installed easily with included calibration instructions. If your Dodge Ram is having problems in idling/speed falls off suddenly or check engine light pops up you are getting codes P2121 P0121 P0122 P0123 then you may have a problem with your throttle position sensor. Our flexible circuit board and hardware are designed to deliver premium performance. Superior resistance to heat and vibration and precisely engineered for easy installation. OE (original equipment) style brackets, hold-downs, hardware, and spacers. Each sensor undergoes a rigorous end-of-line test for reliable, trouble-free operation.

πππππ πππ π.ππ πππππππ
TPS APPS Throttle Position Sensor for 1998-2004 Dodge Ram Cummins 2500 3500 Diesel Bell Crank 5.9L Accelerator Pedal Position Sensor. The throttle position sensor gives information to the ECM (Engine Control Module) about the position of the pedal determining the speed at which the driver is pushing on the accelerator pedal. It is located at the front driver side of the engine inside the bell crank assembly housing in between the cylinder head and batter.

πππππππ ππππ πππππππππππ πππππππππππ: STEP 1 (REMOVAL)
Remove the black Accelerator Pedal Position Sensor (APPS) remove the six mounting bolts and partially pull the assembly away from the engine. Be sure not to place excessive Note: The cables do not need to be removed from the assembly. Disconnect the electrical connector from the APPS assembly. Remove the two Torx screws and remove the sensor.

STEP 2 (INSTALLATION):
Install the new sensor. Tighten the Torx screws just tight enough to hold the sensor in place. Connect the electrical connector to the new sensor. Turn the key to the run position, do not start the engine. Monitor the APPS voltage with the scan tool. APPS voltage can also be monitored by back probing pin 03 on the APPS electrical connector. Rotate the sensor until APPS voltage reads 0.55V +1β 0.050. The set screws should not be adjusted. Tighten the ton screws to a final torque of 50 lb-in. Verify that the reading is still within the specified range after the Torx screws have been tightened. Turn the key to the off position. Reposition the assembly to the engine with the six mounting bolts. Tighten the bolts to a torque of 105 lb-in. Reinstall the black APPS assembly cover.

STEP 3 (CALIBRATION):
Turn the key to the run position, do not start the engine. Press the pedal slowly to the full throttle position and release slowly back to the idle position one time. Clear any DTC's that may have set during the installation procedure.

ππππ ππππππππ

ππππππ

πππππππππ
πππππππππ ππππππ ππππππππ:
π πππ πππ π ππππππππ ππππππππ:
- 1998 - 2004 Dodge Ram 2500 5.9L
- 1998 - 2004 Dodge Ram 3500 5.9L
ππππππππ ππππ πππππππ (πππ):
- 53031576
- 53031576AD
- 53031576AE
- 53031576AH
ππππππ πππ ππππππππ:
The throttle position sensor gives information to the ECM (Engine Control Module) about the position of the pedal determining the speed at which the driver is pushing on the accelerator pedal.
ππππππ ππππππππππ:
This throttle positioning sensor has undergone a rigorous test to ensure high quality under extreme conditions. Features a redesigned housing & circuit board for better resistance against extreme temperatures and vibration.
πππππππ π πππππππ:
- Replaces factory throttle position sensor also known as accelerator position sensor AAPS
- Solves common problem involving engine idle and acceleration
- Resolved common fault codes including P2121, P0121, P0122, P0123

πππππ πππ πππ ππππππ ππππππππ:
- Built to strict quality control standards
- Direct Replacement for a Proper fit and Easy Installation
$45.99 $45.99
$ 21 .99 $21.99
$18.89 $18.89
$ 7 .99 $7.99
$24.99 $24.99
$ 11 .99 $11.99
$38.00 $38.00
$ 16 .99 $16.99
$13.99 $13.99
$ 6 .99 $6.99