Your cart is empty.
Your cart is empty. Please measures level from bottom of swingarm mount bracket to ground. Your distance should be about 14" .
If your distance is too short ,you need cut our kickstand ,please don't buy it if you refuse to DIY it .
If your distance is too long ,our kickstand will be short for your dirtbike ,please don’t buy it .
Aaron Tokhy
Reviewed in the United States on July 8, 2023
The Enduro e-bike comes with a poor quality cast aluminum kickstand that broke after 2 weeks of use while costing twice as much as this conventional gas moto-bike kickstand. Instead, get this steel kickstand for the same price. If I knew this existed I would have bought this.
Andrew
Reviewed in Canada on July 28, 2023
Its decent for its price. Doesnt fit my kx250 2001. useless for me now
Jonathan Broomhead
Reviewed in the United States on June 27, 2023
Bought this to work on my xr400 (which it isn't made for, BTW) and I made it work! Can't speak to the fit for bikes it was made for, it was a little tall for the xr400, but I made it work. The welds are quality, the brackets are plenty beefy for a dirtbike.
Robert B.
Reviewed in the United States on June 11, 2023
I purchased this for my enduro clone electric bike as another review said it works and replaces the absolute junk kickstand that comes with the bike frame. There are 3 problems with this kickstand.The first problem is the welded on foot on the kickstand is not pointing the proper way to be a kickstand… I thought this was a manufacturing error and setup a replacement with Amazon, the replacement they sent has the same off angle foot pointing in a direction not conducive to the bike leaning on it(might be a little hard to see in the picture, but I promise you the foot is pointed the wrong way, and is not parallel with the ground)….The second problem with this kickstand is installing the bottom bolts is excruciatingly hard in the bottom bracket holes. There is material above where the bolts are seated into the holes and threading on the nuts had to be done with a surgical clamp, as basic needle nose pliers didn’t give me the angle I needed…The third problem is the back plate absolutely should’ve been flat instead of sort of horseshoe shaped and most people are going to have to find a piece of metal at a hardware store and drill holes themselves.The last thing I’ll say is this kickstand is relatively tall, and for most bikes, they’re going to have to cut off the foot of the kickstand anyway. My bike has either 24 or 26 inch tires(I honestly can’t remember off the top of my head) which are big wheels for this type of bike and I still need to cut off about an inch of the kickstand. I can’t fall the manufacturer for making the kickstand any one size, but just know you’re probably going to have to cut it.This thing is way over priced as it should be about $20 and is engineered/manufactured poorly, especially for the price. If you can find another solution for your kickstand needs, I would go with that one.
Gil Rand
Reviewed in Canada on December 4, 2023
I bought this hoping it would fit my Kawasaki KDX220R. It was quite nice that it did, and without modifications. I am not a fan of clamp on items, but this fit to the swing frame very tightly. I did not have to adjust the length and the bike stands as stably as any other kick stand. The stand appears to be reasonably well made and strong enough for the job. I did not notice and rattle when riding, which is definitely a bonus. This stand was also WAY less than the other options I could find. The other options were very nice and tucked away differently, but this stand does the job for 1/6 of the price.
Richard cha
Reviewed in the United States on October 28, 2023
I like it because it's heavy duty, but if you planning to put on a stealth bomber swing arm, u need spacer between the swingarm and the unit because it's too wide, also the kickstand needs to be cut depends on how tall your bike is
Matt
Reviewed in the United States on October 2, 2023
Very tight install, had to really work it to get it to fit, an hour later it was on.. Stands the bike up a little tall & almost tips it over but doesn't. C minus for ease of install.
HazEbike
Reviewed in the United States on August 19, 2022
This kickstand works great on the enduro e bike (stealth bomber style frame) with some modification, but it was a right pain in the ass to fit this with the screw hole locations on the lower side.I ended up cutting an equivalent inner plate out of mild 3/16ths steel, and drilled the holes based off of sharpie marks I made using the kickstands original holes. Its sturdiness once installed is great and I hope the galvanizing keeps corrosion away but time will tell. I cut about 2 inches off the bottom and plan to weld on another foot made out of 3/16ths mild steel for stability.Pros:- Sturdy- Decent coating from the factory.- ease of use after installed?Cons:- M******F@%& the guy who decided the angle for the lower mount.- Should come with a spare backing plate thats flat, icnreasing options.- Pricey for the amount steel and springs cost.- adjustable length would have been nice in some way, threaded foot etc.
CryptoFlights
Reviewed in the United States on July 21, 2022
I bought a 12000w 72v ebike from China and kickstand broke in 30 days,This is real deal
kolt
Reviewed in the United States on September 2, 2021
Does not fit 96 cr250r and I’m outside my return window. So it’s a pile of junk
Recommended Products
