Your cart is empty.
Your cart is empty. How to install a band saw tires
1.Disassemble the wheel from the saw.
2.Remove the old tires and clean any debris and adhesive from the wheel.
3.Try to place a part of tire on the wheel and fix it by spring clamp, and then use another spring clamp to fix the tires on the other side, as symmetrically as you can.
4.Stretching the tire onto the wheel completely. You may need to use a pry tool to help the tire onto the wheel. Be sure to avoid sharp edges. Take down the spring clamps.
5.Even out the stretch. Do this by inserting a round object such as a dowel rod between the tire and the wheel and rotating it around the wheel a couple times.
6.Re-assemble your saw and set it up according to your saw's owner's manual.
Roanna Burnell
Reviewed in the United States on February 2, 2025
Perfect fit, it was fitting a bike tire.
D.
Reviewed in the United States on September 16, 2024
Finally replaced the tires on my saw and these worked great ! Easy to install and perfect fit. It's just as smooth and quiet as when it was new. Great value. Manny Thanks.
Believer
Reviewed in the United States on July 21, 2024
a bit of a challenge to put on, however putting tire in hot water for a while softened it up enough to make the installation easier. Its a good product.
Robert Lake
Reviewed in Canada on July 21, 2024
Well, they fit nicely. Took some effort to get on, but that's expected. Just took my time and clamped it down as you stretch it over so it doesn't pop out as you go along.Can't attest to durability or performance as I have yet to use the bandsaw with the new tires yet.
Dennis Powell
Reviewed in the United States on July 17, 2024
Installed on an old Delta 10" saw. Snug fit to get over the wheels, but it needs to be snug to work properly. Works great. Would buy again if needed.
Hilary
Reviewed in the United States on May 29, 2024
Wanted to spruce up the late FIL's old 10" Rockwell and being out of my comfort zone doing anything wood related, I read some reviews and picked up these urethane tires. I popped the last old rubber tire off the wheel, spun them both around by hand while holding a stainless wire brush to the mount surface and they cleaned up well. One of the videos suggested putting the tires in hot tap water for a few minutes and I'm sure doing this helped them slip right on w/o any issues. They were the perfect width and a nice snug diameter. If swapping out your old tired tires is on your to-do list grab a set of these and you wont be disappointed.
P. NORMAN
Reviewed in the United States on March 21, 2024
These tires fit my Delta bandsaw perfectly & made it run smoothly again. Took some doing to install but they worked great.
roy
Reviewed in the United States on February 4, 2024
They seem to be good quality. Very happy. Trick is to strech tight as possible immediately as installing. Went on fairly easily with some elbow grease.
DougWW
Reviewed in Canada on December 4, 2024
These go on well and seem to wear well. They are a bit thicker than the factory tires too.
Phatman
Reviewed in Canada on November 10, 2024
Used these tires to repair an older bandsaw , they worked excellent and solved the problem from the old worn out ones
Larry J Parks
Reviewed in Canada on September 23, 2023
WORKED VERY WELL A GOOD PRODUCT
Kris
Reviewed in the United States on August 6, 2023
I put this on an older Skill band saw that the original rubber tires had finally deteriorated and fallen apart. It took me more time to clean the old glue off the wheels that it did to install these. My saw is up and working again so I’m happy.
Michel C.
Reviewed in Canada on November 25, 2023
Was easy to install and works great
Recommended Products
$58.19
$ 28 .99 $28.99
$12.50
$ 5 .99 $5.99
$12.09
$ 6 .99 $6.99