Your cart is empty.
Your cart is empty. Specification:
Product Name: Potentiometer
Resistance Value: 10k Ohm
Adjustment Type: Slide adjustment
Type: Double linear rotary
Material: Metal + Plastic
Body Size: 60 * 8.5 * 6mm / 2.36 * 0.33 * 0.24inch(pin not included)
Total length: 60 mm /2.36inch
Mechanical Characteristic:
Operating Force: 0.2-2N(20-200gf)
Stopper Strength: 50N(500gf)measuring point=5mm
Lever Wobble: 2*(2*L)mm max.
Bending Moment: 25mN.m(250gf.cm)
Push Pull Strength: 50N(5kgf)
Click Slip-out Force: 0.3-2.5N(30-250gf)
Level Deviation: 0.5 max.(one side)
Package Content:
10 * 10K Ohm Slide Potentiometer
Saycco One
Reviewed in Spain on February 20, 2025
los compre para una mesa de mezclas algo viejita pero que ya no funcionaba en estéreo así que cambie todos los potenciómetros y le he dado nueva vida y funciona como cuando estaba nueva sin ese molesto ruido que hacen cuando no hay buen contacto
M01
Reviewed in Germany on March 3, 2024
Anwendung in einem Mischpult für den Hobbygebrauch, dafür sind sie ausreichend, schön leichtgängig.Für den profesionellen Einsatz würde ich sie nicht anwenden, Robustheit und Lebensdauer?
tomas
Reviewed in Spain on February 2, 2024
cumplen con su cometido y van perfectos.
Jude
Reviewed in the United States on July 17, 2022
Im using on my diy things it works and a smooth slider
Patrick
Reviewed in the United Kingdom on December 19, 2022
good quality and work as expected, maybe a little pricy though
Daniel Byrd
Reviewed in the United States on November 11, 2022
Did not realize these were stereo slider pots when ordered. Would not have been a problem if I could find a Datasheet with a pin out (I could not). Wired these up to my Arduino, tested, board shorted to ground when I moved the slider. Tried rewiring, got the same result every time. Still have 2 left, but too frustrated to use.
Enderkruemel
Reviewed in Germany on October 20, 2022
Leider sind einige pins beim Versand gebogen wurden.(kein Problem, nur etwas nervig wieder zu richten.)Es gibt außerdem auch kein Pinnbelegungsdiagramm. Das macht es etwas schwierig zu finden welcher pin was macht. (Ein einfaches Bild wurde da reichen.) Kostet ja nichts weiter so nen Zettel da mit rein zu packen...Die potis sind auch generell etwas ölig.(Kann man ja aber mit zb einem Küchentuch und etwas Spiritus abwischen.)Ist beim Einbau etwas nervig aber ist ok.Meine Befürchtung war,dass sich auf lange Zeit durch das ölige,viel Staub ansammeln könnte, was aber Großteils durch die Abdeckung verhindert wird.Jedenfalls kann ich die nur weiterempfehlen.
J. C. Rice
Reviewed in the United States on September 25, 2021
Super smooth gliding action gives this pot plenty of user appeal.The "linear" response isn't exactly so: as the attached graph shows, there are ease-in and ease-out ranges near the ends. Minus one star for this quirk. Also note that I measured 11kOhm as opposed to the rated 10; not a big deal for my use.
Jes
Reviewed in the United States on March 7, 2021
Smooth slide and they are reasonably accurate
David Wall
Reviewed in the United States on September 19, 2020
I think this was designed for audio applications, but it works great for robotics. Used it to get position feedback from a finger on a robotic hand design. Tied it into an analog input of an Arduino NANO with 3.3v to GND. I've seen it available in multiple lengths, but I used 60mm. I like that it has (2) M2 threaded holes for mounting, very secure. My initial impression was that it has a solid design, and glides very smoothly. I only needed 1 POT, but it comes with DUAL 10K POTs. I highly recommend this potentiometer.
Danielle Norris
Reviewed in the United States on February 21, 2020
Prototyping with an Arduino Micro. Works perfectly fine.
Art
Reviewed in the United States on September 23, 2019
These work perfect for my Astatic Echo Master 2000.
Jason Y.
Reviewed in the United States on November 13, 2019
they work as advertised and good price -- but if you are doing an arduino project beware, the leads are two small to snugly fit into a breadboard, they come out very easily. I'm gonna have to buy a perfboard tomorrow and solder them -- not ideal.
Recommended Products
