Your cart is empty.
Your cart is empty.Ideal for applications with limited space. Locking patch available upon request. Plunger does not lock in fully retracted position. On stainless models, all parts are stainless steel except for the ring which is nickel plated steel
jon jon
Reviewed in the United States on February 16, 2025
These work great I bought a self taping drill bit
Redmond
Reviewed in the United States on August 26, 2023
Following some other instructions and adding some color of my own for the Packout rolling tool box mod (I was trying to get it into the trunk of my car without laying on it's side): 1) Remove sheet metal screws on back of bottom of Packout box holding in the current handle; 2) Remove handle completely; 3) Drill both the original holes in the metal handle and holes in plastic of tool box with 3/16" bit (this came from another poster and it's a really good fit), trying to drill through both the plastic and the metal at the same time can be a little tricky because you are trying to keep everything lined up so save yourself the trouble and drill them separately - you just want to go through the first layer of metal; 4) Tap the plastic hole with a 1/4 x20 tap (or alternatively use a 1/4 x 20 bolt and a ratchet but go slow since you don't have the benefit of the taper on the tap); 5) Screw in the part, you won't get it that far in because you lose a bit of purchase on it and it just starts to spin; 6) remove the ring temporarily; 7) find a 1/4" shallow wall nut driver and tighten more (I tightened mine until just a bit of the ring hole was inside the box and had to sand a bit of the outside of my nut driver to get it in); I've read a few people say the part wasn't long enough and I think it's probably just not in far enough); 8) put back on the ring; 9) slide in handle and voila. Took my sub 10 mins. I haven't punished this thing much but so far feels very solid.
Kerry P
Reviewed in the United States on May 2, 2023
The media could not be loaded.
Nanibush
Reviewed in Canada on May 22, 2022
Good just have to drill the metal out on Milwaukee packout
jjvw
Reviewed in the United States on March 15, 2022
Bought these to use for the Milwaukee PackOut handle removal modification. But the threaded portion is too short to reach as far as is needed to secure the handle. Not sure how other reviewers are able to make it work. A 0.5" thread length is what is required.There is nothing obviously wrong with the spring pin itself. It just won't work for this purpose.
Kindle Customer
Reviewed in the United States on September 14, 2021
One of the big downers of the Packout rolling toolbox is that the handle doesn't drop flush to the top of the box. If you are trying to stuff this box into a trunk, that's a big problem. These little guys help alleviate that issue by letting you remove the handle easily. You just remove the two screws that hold the handle in, thread the plastic with a tap that matches the threads on these spring plungers, screw them into the plastic then drill the two holes in the handles just a tad bit bigger so the plungers will go into them. Done. now all you have to do to pop the handle out is pull on the two plungers. Easy peasy! Now you can close your trunk!
RJ
Reviewed in Canada on August 10, 2021
Worked perfect for Milwaukee Packout.
Max
Reviewed in Canada on July 25, 2021
Perfectly fit my Milwaukee Packout for removing the handle!
Smokie
Reviewed in the United States on July 23, 2021
Tapped for 1/4-20 tread, used the same drill bit to enlarge the hole in the handle the sheet metal screws were in. The only issue is the handle is very tight as it was not designed to be taken on/off, lubed with some light oil works great.
FILIP BIMMER
Reviewed in Canada on June 1, 2021
Je recommande, bon produit
Quantis
Reviewed in Canada on June 15, 2020
Used to make the handle of my Milwaukee packout boxes removable. Super simple install and well made.
Christopher Wegner
Reviewed in the United States on March 31, 2020
When I received the item the pin was stuck and wouldn't compress. With a little force it freed and works perfectly now. Used as a location pin for my boat electronics slide mount. Looks like good quality materials.
BH6W
Reviewed in the United States on July 21, 2016
This works for my intended purposes. It's stainless steel, and the build quality is high. The spring is also firm enough that you can rely on it not failing.The price could be a little lower IMO.
Recommended Products
