Your cart is empty.
Your cart is empty.Product Description
Product Advantages:
The TB1H is a high performance microstepping driver based on the latest original for high-efficiency TB6600HG for IC. The TB6600HG adopts single-chip PWM bipolar sinusoidal chopper to ensure the low vibration and high efficiency.
IC parameter:
- 5 subdivision mode options (1/1, 1/2, 1/4, 1/8, 1/16,1/32).
- output current: IOUT = 4.0A (peak, in 100ms).
- rated output: IOUT = 3.5 A.
- package: HZIP25 - 1.00F.
- input port internal pull-down resistor: 100 K.
- alarm output pin current:Ialert = 1mA.
- monitoring output pin (MO): Imo= 1mA.
- with reset and enable pin.
- with standby function.
Feature:
- H bridge bipolar constant phase flow drive.
- the maximum 4.0A of the eight kinds of output current.
- the largest 32 subdivision of the 6 models are optional.
- input signal high speed photoelectric isolation.
- common-anodestandard single pulse interface.
- semi closed enclosure can be adapted to a more stringent environment.
- to provide energy-saving semi-automatic current lock function.
- built-in temperature protection and over current protection.
William Weslow
Reviewed in the United States on January 28, 2025
They were coo-owl.
Mark
Reviewed in Canada on May 27, 2024
Higher voltage and smaller like Geckos size would be better , but low cost and work great!
Rene Paredes
Reviewed in the United States on December 7, 2024
me llego uno en mal estado, los demás bien
HARVEY BEVERLY
Reviewed in the United States on November 20, 2024
Nice packing, seems well constructed.
Johnvk
Reviewed in Canada on April 5, 2024
4 units arrived in good shape and work great.I’ve been using them for about two years without any issues.
ben
Reviewed in the United Kingdom on September 18, 2023
Haven't got round to using straight away but soon as a needed them 1 out of 4 workedNeeds some serious quality control putting in place
Customer
Reviewed in the United States on December 23, 2023
Very good product!!!
nixon lange
Reviewed in Canada on May 9, 2022
Hobit
Gil Rand
Reviewed in Canada on March 6, 2021
Nice light unit that works as advertised for smallish motors. Worked fine for a 3.5A motor and is adjustable over a wide range of divider ratios and current limiting.
Dr. Tim Ambrose
Reviewed in the United States on March 11, 2020
Built in filter capacitors and current regulation and microstepping! Awesome!They work very well and don't burn out when I stress the stepper motors over and over with abuse current curves like abrupt stops and such. These are not the expensive top shelf name-brand kind, but they work great. Virtually no reduction in quality that I can see considering they are a third-party alternative to the top shelf expensive ones of the same size and greater weight.
Nightpainter308
Reviewed in the United States on September 2, 2019
They work great and are too easy to set up. You can't go wrong with the value vs cost.
Flamewake
Reviewed in the United States on August 3, 2019
They arrived quickly and in good condition, however they are a bit lacking in instructions. I highly recommend finding a complete guide for building a cnc machine or 3d printer and using the parts they list as configuring these and the Arduino has been quite an ordeal. I'm going to test them with an NVUM v2 controller soon and I will try to update this after as to if they worked or not, but I believe they will. Not the absolute cheapest and all of these tb6600s on Amazon look pretty similar, but I'm happy with them. They have been more than capable of driving Nema23 175oz 2.8A motors.
Joe
Reviewed in the United States on July 8, 2019
These stepper drivers work as expected. I'm driving them from my controller and they work fine. The housing is thin gauge metal, so it may be bent a bit, but it doesn't effect the product. There is a large heatsink on the back. I put all 4 in a case with a single fan.I'm using a 15amp 24v power supply to power all 4 and have 2 for the y-axis and one for the x and z. The x and y axis drivers are setup for 3amps and the z for 2amps. Be sure your power supply has the capacity for all the motors to be driven at the same time. Also set the current output based on your stepper motor spec sheet. Higher currents produce more heat in the stepper motors, but give much better results.One last note I haven't opened one yet, but will before I start using them on the cnc machines I plan to sell. Also not all stepper motors are the same. Even ones with the same size and current rating can give different results. I'll update this review when I finally open one.
Recommended Products
$329.95
$ 99 .00 $99.00
$11.39
$ 5 .99 $5.99