Your cart is empty.
Your cart is empty.Product Description
Aideepen 5pcs Dual H-Bridge DC Stepper 1.5A 2 Way DC Motor Driver Module Replace Stepper L298N for Smart Car Power
- Use of imported original chip, built-in low on-resistance MOS switch
- Dual H-bridge motor driver, can drive two DC motors or a 4-wire two-phase stepper motor
- Dual 1.5A * 2, the peak current to be 2.5A, built-in thermal protection circuit, do not be afraid motor stall burned, automatic recovery after the temperature dropped
- Minimal heat, no heat sink, small size, low power consumption, is ideal for battery powered
- Small size, light weight, low standby current, is the ideal choice for your car model
AJB
Reviewed in the United States on February 23, 2024
Documation is a bit difficult to find but the boards are fine. Very versatile.
Richard
Reviewed in the United States on June 5, 2022
I ordered these 5V power (regulated from LiPO battery) to run the motors on a small robot/RC. It worked as a drop in replacement for a LN298, but doesn't have the voltage dropoff and is a much smaller size.The board was very professionally packaged and has quality construction. A nice breakout board.
A Customer
Reviewed in the United States on June 22, 2021
I really like these, good value for money, compact and very capable - just know & understand the voltage limitation before you order.
Scott
Reviewed in Canada on April 22, 2021
Its nice and small, great for tiny projects .works with low power motors .The IC is not 'L298N" , its some other one i forget the chip name,for small projects this is a better chip , only need 2 GPIO per motor , if you need reversing , 1 if not .It can control smaller motors at lower voltages very well, that the L298N chip would not .Pin pitch is non standard , cant alight with bread boards or perf boards.Power in is non standard pin pitch .while each motor channels input pins and out put pins are standard pin pitch ( the 2 wires) , the pairs them selves are not laid out in normal pin pitch . Mildly annoying if you intend to use a few in a project .I suspect they were intended to be used inline like an R/C esc , so overall pin pitch is not a issue .That said, they are great for RC projects, small projects .I will buy again .
Noel Gonzalez
Reviewed in the United States on September 16, 2020
Great little board that is working well for me. But as noted by others, this board uses the better MX1508 chip rather than the titled L298N. If you need to use an Arduino library use one compatible with the MX1508 for it to work correctly. This board does not need or use an Enable signal.
NerdyPhysicsGuy
Reviewed in the United States on September 13, 2020
These H-bridge drivers are perfect for driving small brushed DC motors found in DIY robot kits and even remote-control cars. They're very easy to set up and have clearly-marked connectors. With the loads I've been putting on these (small 6V DC motors, 0.5A), they don't heat up at all.Be aware that these boards do not come with pre-soldered pin headers, so you'll need to provide your own.
Grimm
Reviewed in the United States on August 14, 2020
super tiny and work fantastic. If you are wondering about these, just try them out! Don't let being new or unfamiliar with code drive you away from these if you need speed control. Power indicating led is not needed or a wanted feature of mine. The price is low and I ordering more after this review.
Rick White
Reviewed in the United States on December 22, 2020
The small size makes it perfect for DIY RC cars.
Paul
Reviewed in the United States on September 6, 2019
Great little motor/stepper controller! Great value! This is a simple to use board that can be used to control 2 DC motors or 1 stepper motor. Works great!
Customer
Reviewed in Canada on October 18, 2019
This is not L298N part. It is MX1508 instead, which is much better than L298N. It drops less voltage, and only requires 2 pins to control the motor (L298 requires 3 pins per motor). This particular module is good for small DC motors only, so check the specification and make sure your motor will be okay with the allowed voltage and current. If you need to drive big motors (above 10V and/or 1.5 Amps) you will need a different motor driver. But if your motor requires less than that, then this driver is perfect.
Recommended Products
$299.22
$ 99 .00 $99.00