Your cart is empty.
Your cart is empty. The PoE Splitter splits a PoE signal into an 5VDC power and 10/100Mbps ethernet data source.
This device allows you to run ethernet cables from a PoE Switch over long distance, and then split the PoE signal into a separate data signal and 5Vdc power sources in order to run an non-PoE devices.
Specifications:
Input: 44-56VDC max ; Shielded RJ-45 female;
Output: 5VDC 2.4A 12W; RJ-45 male
DC Jack: Micro USB
Length of Micro USB cable: 19.5cm
Operating Ambient Temperature: -10 to 45℃
Regulatory IEEE 802.3af
What is included
4x 5V PoE splitter
Note: this 5V PoE spitter is only compatible with 10/100Mbps non-PoE devices, it DOES NOT support gigabit non-PoE devices like Raspberry Pi 3B+
Matthew W.
Reviewed in the United States on January 19, 2025
This does exactly what it was inteded to do
Ben R.
Reviewed in the United States on September 2, 2024
Working well to power multiple Wyze cameras. All have been running for months without any problems. Very pleased.
Charles Payne
Reviewed in the United States on May 26, 2024
I needed PoE Hats for a project, come to find out there are not PoE hats for the Libre Computer Renegade boards. Lucky someone recommend these PoE Splitter, until the recommendation, I never know about such a device.The splitter work great. Saving me a lot of space, no need for another power splitter to run my Renegade boards.
Andreas
Reviewed in Germany on March 8, 2024
tolle erfindung, funktioniert einwandfrei
BjL
Reviewed in the United States on March 26, 2024
I used my existing Cat 6 wiring along with a POE switch to provide USB power to my Blink cameras. Brilliant solution!
shopper
Reviewed in the United States on November 19, 2024
Works to make old rpi into IP cam.
JerseyGuy
Reviewed in the United States on April 14, 2024
I used a few of these to power some Vonage ATA’s from my PoE switches. We take our phone lines with us when moving between our two homes, and this makes everything so much simpler than dealing with the wall-wart power adapters that the ATA’s came with. Well worth the money to only have to worry about plugging-in an Ethernet cable vs. that and a power cable.Been using it for about a month now without issue.
Doctorshadowmerchant
Reviewed in the United States on August 29, 2023
This splits power from network traffic, so if you have a wifi only camera that needs power, and you have previously setup PoE through ethernet cable to the location, this will save you needing to thing about a power transformer or electrical box at the location.I have a few Wyze cameras set where there is PoE cabling, so I just split the power and use the camera's wifi to connect to the network.For those of you with PoE cameras already, this is not needed.
Burtingam
Reviewed in Canada on August 21, 2023
Impossible de parler avec le service à la clientèle de la compagnie. L'un des 4 items est défectueux et aucune assistance possible.L'alimentation de l'un des 4 ne fourni pas de 5v. Ils offrent une garantie de 2 ans à ce que j'ai lu... J'attend toujours de parler à quelqu'un
a*f*
Reviewed in Turkey on April 4, 2023
2.4 amper yazıyor ama 2 amper gücü kesiyor
Neba
Reviewed in the United States on June 13, 2021
bought these to power some wyze cams I had put dafang firmware on. same camera, same port on the switch, 2 out of 4 worked. it was a cisco switch, and 'show power inline' showed 'faulty' whenever 2 of the poe adapters were plugged in. I changed ports, and cameras (I had 9), even cables. it always read 'faulty' and the cameras would not turn on. seems like poor quality control and I essentially paid $30 for 2 adapters. the working ones are in the attic powering cameras below in the house. no worth returning, but maybe someone else will save some time and money.
C WARD
Reviewed in the United Kingdom on June 11, 2021
I had about 12 raspberry pi 2 that were using a TVs USB port for power. Decided to look at using PoE to power them instead, and these work just fine. Also did a test on a 3B Pi, and then seemed to work fine too.
Lancelot Williams
Reviewed in Canada on December 21, 2021
I bought these to power four WiFi IP cameras that only work on USB power, specifically 5V 1.0A. The power adapters that came with the cameras have titillatingly short cables which are moulded to the adapter, and I didn't want to make it easy for my children to disconnect the power to the cameras or move them around, so I decided to mount them on the ceiling and see if I could use the USB PoE splitters to power the cameras from a HP ProCurve switch. I tested each splitter individually on a 100-foot CAT6 cable powered by the switch, and the cameras booted right up and returned to their last positions with no issues whatsoever.Next test is for my older WiFi routers with a pair of 9V splitters from the same company; TP-Link said it wouldn't work but I think Anvision will prove them wrong.
Recommended Products
