Your cart is empty.
Your cart is empty.Ditch that plain-Jane stock appearance once and for all. AVS Hood Scoops add 200HP in looks alone. Its heat-resistant, UV-protected, thermoplastic material is built to last a lifetime delivering unmistakable eye appeal wherever you go. Available in smooth black finish with paintable surface so you can match your factory paint if you like. Choose from several styles and sizes in 1- and 2-piece options. Cleanly mounts with 3M automotive-grade adhesive tape concealed. Backed by a limited lifetime warranty
Raine Iron
Reviewed in Canada on January 5, 2025
If installed following the directions given, they stick well. Went on the highways in the Saskatchewan winters. Also, a deadly appearance, I bought 2 of them 😎
Don
Reviewed in the United States on September 9, 2023
I changed the 3M tape as the stuff that came on it, it’s not worth a pot. The plastic grill insert bowed so bad that I rubberbanded it around a coffee can for a week to try to shape it so it would not bow out. Looks good but will test it this winter.
andrew carriere
Reviewed in Canada on July 12, 2023
great product
Ashley Walker
Reviewed in the United States on May 26, 2023
Fit on my 1995 Mustang GT with some fabrication, few pop rivets later it's not going anywhere! I did drill out each hole to make the grill functional as well. Worth the money if you know what you are doing.
Fritzie
Reviewed in the United States on January 20, 2023
I liked everything about this hood scoop it fit on my 2000 Dodge Dakota didn't think it would was very easy to install if you followed the instructions and it looks terrific
John blaze
Reviewed in the United States on March 16, 2022
2011 chevrolet silverado, the adhesion sticks well, very easy to install, price is worth it thanks.
Rob Labrie
Reviewed in Canada on July 31, 2021
easy fit , fair price . Needed it to cover up a hole I cut out in my hood. sticks great with the 2 way tape it comes with already on it. I had to bend the front corners down because my hood has a curve to it, but I just pop riveted the 2 front corners and it was good to go. the adhesive is strong enough to hold it down
Donald L.
Reviewed in the United States on July 20, 2021
Was a cool scoop, overpriced for the cheap plastic that it was. But I was ok with that because I didn’t care about the price. However when I opened it and there were scratches all over it, completely unusable, I got aggravated and sent it back. The packaging was not adequate. I don’t see how any of these make it to consumers without being scratched all over
Rob
Reviewed in the United States on June 10, 2020
Just the size and profile I needed for my Impala. Low profile, wide, and longer than the smaller ones they sell on Amazon.I skipped the 3M tape, peeled it off, threw it away. Applied glue to adhere the decorative intake to the scoop. Drilled holes (with patience) through each existing hole in the intake and through the scoop itself, so now there are actual holes in the intake. Applied LED light strip inside the scoop behind the intake holes. Boom, light-up hood scoop. Definitely bought the right product. Could be a few bucks cheaper. But you get what you pay for.
GB
Reviewed in Canada on January 29, 2020
Excellent
Simmer
Reviewed in the United States on September 2, 2018
I initially bought this to install on my Jeep Wrangler. The scoop has a slight curve to it, however, the jeep hood is fairly flat. The stickers on the scoop (supposed to be 3M, but I didnt see the 3M logo on mine) would probably have held it down in place, but I didnt expect it too hold on against the fight of the curve and wind for a long period of time. Also, I bought used, and although it was 'Like New' condition, it was scuffed up a bit. According to Amazon, like new should be be scratched. It wasn't over the top, but still. It would have needed to be painted.Another thing to note that is not easy to tell in the picture is the vent portion is not open. Which makes sense because the wind would have gotten in there and sent this thing into orbit if it was open. The vent they have pictured is actually a sticker with holes in it. anyone getting up close would be able to tell.In the end I sending it back and will save for a complete hood replacement with the scoops and air vents built in.
Buzyeric
Reviewed in the United States on November 30, 2018
Exactly what I was looking for. I wanted that Aston Martin look. This was the closest I could find. The low-rise inlet and a very thin tapering to the rear made a beautiful silhouette from all angles on my solstice. Because I put it so low on my hood the two front tips were not able to adhere. To make sure that they were made flush I decided to use automotive epoxy glue in lieu tape.
Tammy/Mike Legault
Reviewed in Canada on August 23, 2015
the quality of the hood was up there, but it is definitely NOT suitable for a 2005 Dodge Ram,it is WAY to small, i would say it is made for a car hood.I purchased the Wade 72-14001 28" from amazon and it fits perfectly almost like the rumble bee scoop although on amazon it said not suitable for my truck i went directly to the Westin site and it says yes for the 05 Ram., Hope this helps.
Recommended Products
