Your cart is empty.
Your cart is empty.Product Description
AXA-1# Holder and AXA-2#
250-101 Turning Tool Holder , use tool bit up to 1/2"
250-102 Boring, Turning Tool Holder, use tool bit up to 1/2" and round shank tool bits up to 7/16"
AXA-4# Holder and AXA-7#
250-104 Heavy Duty Boring Bar Holder, use 5/8 and 3/4 shank boring bars
250-107 Parting blade tool holder, use 1/2" height parting blades
AXA-10# Holder
250 -110 Knurling and Turning Tool Holder
AXA Wedge Type Quick Change Tool Post for Lathe 6-12"
- Precision-engineered to assure repetitive accuracy. Quickly and easily installed on an engine, bench, or turret lathe for a wide range of perations
- Includes axa tool post with rigid wedge design, easily centered; axa #1 turning & facing holder with 3/16-1/2" capacity; axa #2 turning, facing & boring holder with 3/16-1/2" capacity and groove for round tools; axa #4 boring bar holder holds 5/8" tool; axa #7 universal parting blade holder for use with 1/2" or smaller blades havind parallel top & bottom; axa #10 knurling, turning & facing holder with two knurls
- For use on lathes with up to 12" swing (defined as the diameter that can be turned over the bed)
- Fully interchangeable with Aloris, Dorian, Phase II, Yuasa, and most other manufacturer components
- The tool post comes with a blank T-Nut plate, the customers have to machine it according to the size of their own specific lathe T slot
Jim
Reviewed in Canada on February 8, 2025
I did not notice that the boring bar holder is for 5/8" unlike the rest of the holders in the set, which take 1/2" tool bars. Just gotta say WTF? Have not used any of it yet so my rating of 1 star was based on this alone.
Tracy c
Reviewed in the United States on February 7, 2025
Works as it is intended
Meshuggana
Reviewed in Canada on June 16, 2024
Seems to be descent quality and the base plate was machinable to modify and fit my lathe.
Dtom
Reviewed in the United States on June 14, 2024
it arrived in good time and was easy to set up the t slot block came WAY oversized for my 1940s atlis lathe but I consider that a good thing was easy for me to mill to spec the tooling seems high quality easy to adjust height it locks down tight and doesn't move 10/10
LBKewee
Reviewed in the United States on March 6, 2024
Really sturdy!
Karmen Datema
Reviewed in the United States on April 11, 2024
Ok, I'm not a "machinist " but, for the cost, the fit and finish is very good and tolerances are good. I am very happy.I guess if there is a bad side; the handle clamp and release are a little less smooth than I'd ideally like. But, I am very happy.
Jimxxxx
Reviewed in Canada on September 12, 2022
Product arrived as described. Using this on a King Canada mill lathe combo. Replaced the standard tool post with this unit. After a few measurements it wasn't difficult to machine a new centre bolt that would fit the 12mm t-nut of the lathe. Very pleased on the difference in cut Using the new post. Much smoother and no movement. Will confirm with a dial indicator exactly how much better, but visually it looks substantial.
Mother Wilson
Reviewed in the United States on August 14, 2022
I got it installed and the holders only fit one side. I cannot see how to contact the seller. I will probably modify the holder to try to get it working. From tne other reviews it is probably just a bad one. But it has been to long to return.After a little file work everything fit. It was not the handle angle
PROTO Industrial
Reviewed in Mexico on December 28, 2022
Llevo utilizando la torreta de cambio rápido 6 semanas (qué por cierto nunca las había utizado) y es una maravilla para tu torno manual. Si tienes un torno entre 9" ~ 12" de volteo, no dudes en comprar éste Kit y ahorrar muchísimo tiempo cambiando y ajustando herramientas, es una excelente inversión ¡no te arrepentirás...!
Curtis
Reviewed in the United States on August 1, 2021
Perfect for a home shop lathe. No way I could justify spending 3-4x the money for an Aloris or comparable. It’s a simple mechanism. Put it on my Clausing 100. Needed to machine the block for the compound but that’s to be expected. I just wish the handle took less rotation to move the wedge. I’ve run into having to remove the handle to get tool holders out but that’s rare.
Veritas
Reviewed in the United States on October 19, 2021
easy install, bought a 9/16 -18 tap and drill combo for 15$, drilled out slide, took maybe 30 min. easy install on grizzly g4000. seems nice, havent actually used yet. if it blows up, ill change my rating. i am a rank amateur and new to machining generally, so this is my first toolpost aside from the stock one. seems easy to adjust and very stout. i am glad i bought.
Nate
Reviewed in the United States on April 14, 2020
It is a lot better then the lantern holder I was using before it, it was easy to set the height and it was pretty easy to modify the 1/2" tool holder blocks to 5/8" I just took out the set screws and evenly as I could ground and cut away from the top, "where set screws come through and hold the tool" about 1-2mm, it made a tight fit but I prefer my tools to not have a ton of wiggle room. This action my not be recommended but i didn't have a lot of money to buy the 5/8" holds out of the gate so, you just make do. Cons, there seems to be some play in the mechanism that drives the wedges but not enough to be an issue.
Recommended Products
$129.99
$ 56 .99 $56.99
$15.50
$ 7 .99 $7.99