Your cart is empty.
Your cart is empty.Bosch TS1016 extends 18-Inch and stores flush to table. It extends the working depth of Bosch 4000, 4100, GTS1041A 10-inch table saw. It features hardened metal construction; aluminum mounts and includes table saw extension. The table saw is not included.
Thom Thompson
Reviewed in the United States on March 15, 2025
Item works well once you have it installed. Small space for big hands to get all the bolts in place. Don’t understand why the item has extra brackets that are not needed for this model of table saw.
haley m.
Reviewed in the United States on September 30, 2024
Unfortunately I had to return. Other reviews stated they had extra parts but I was missing parts. Even had 1 piece that looked nothing like pictures and I got no fasteners not sure what I was missing because it also had no instructions. Very disappointing as I needed thos now and can't wait for a replacement
Owebo
Reviewed in the United States on April 6, 2024
It shipped super fast and installed on my 4100 really easy. It fills that void between small work the saw can handle on its own and large work you need a roller stand for. Immediately put it to use on ripping butcher block bench tops and was not disappointed how it handled the heavy loads. Your saw is missing this and it is worth the investment.The only drawback is the dinky detent knob….seriously Bosch?
Customer
Reviewed in Canada on September 2, 2023
This outfeed support bolted right on to my Bosch 4100 table saw. It works great and makes handling larger material a lot easier. Excellent quality.
Bradley
Reviewed in the United States on July 28, 2023
No real complaints about the item. Installed easily and serves the intended purpose well. But really, hard to grasp why this wasn't included with the saw/more integrated. It's such a simple and obvious assembly.Also surprising how many parts it comes with that aren't needed for a particular saw. Seems wasteful.It does add a fair amount of weight so with this plus the left side support, your portable saw starts to weigh a pretty substantial amount so consider that if you lift your saw into a pickup bed or similar.
Jean Lemire
Reviewed in Canada on January 15, 2023
After waiting a bit for news from Bosch I received a new box containing the rear outfield support. No mail, no message, just a box near my front door.This time the content was correct with two plates to fit either my 4100 model or the 1040 model. Of course, as previously, there where also two trunnions for each plates so that half of the parts contained in the box will be stored to gather dust since I don't need them on my saw.I give only 4 stars because of that last point. Otherwise it would be 5 stars. The outfield support as well as the left support, that I also added to my saw, work correctly and do not interfere with other accessories nor with the gravity rise support. Some bolts are difficult to put in place for the right trunion but I succeeded. I also discovered that the rods diameter seems larger than the one on the outfield support that I had installed on my former 4000 model.My only suggestion to Bosch is to offer this accessory for only one saw model, thus avoiding material waste and higher price for the customer.
DonOutdoors
Reviewed in Canada on March 12, 2022
Fairly easy to install on my Bosch 4100-10 saw. Doesn't add too much weight. Comes in very handy when cutting long pieces.
FD
Reviewed in Canada on October 13, 2022
This Bosch outfeed fence fit and worked perfectly on my table saw. Highly recommended.
KokoMan
Reviewed in the United States on April 5, 2021
This is for 4100 and GTS. You can apply what I did for either one.I made table extension out of rail replacement parts, plywood and some other parts. Nothing fancy. When you buy this back extension it will come with almost two sets. One for 4100 and other for GTS. except slide bars. I used extras to extend "extension" to accommodate my ""extension"" on the left side of the table. All you need is to drill two holes (Your choice of offset) in extra support and you are done. It is like everything from Bosch. Brick house and good R&D. Have fun!
Rolidnot
Reviewed in the United States on May 15, 2019
I have a model 4100 Bosch portable table saw. This outfeed extension kit has parts for THREE models - the 4000 & 4100 (which are the same setup) and the GTS1041A Bosch saw.Rather than make two extension kits for the 4000/4100 and the GTS1041A which is the $2200 auto stop version that shuts down when it detects flesh, leave it the Germans to give me extra parts for the GTS1041A saw that I will never use. Sure, I can throw them out but it's incredibly wasteful.Check out my attached photo for the "extra" parts included which you don't need for the 4000 or 4100 saws (the cat does not come with the extension kit). There are two extra rail mounts and the 12 gauge outfeed support for the GTS1041A. What's weird is that the outfeed extension comes with the GTS1041A - for $2200 it had better come with the saw so why they sell it as an accessory is classic Teutonic logic.The extra parts make initial setup a little confusing and reading the directions eventually helps once you figure out that you have useless parts in the extension kit. It's simple enough to install once you put the extra parts aside.The actual extension works OK. I wish the locking knob were larger diameter and Bosch would include a ball end hex wrench which is really helpful for installing the hex/Allen bolts. The kit could be $15 cheaper if they eliminated the extra outfeed support and the mount for the rails meant for the GTS1041A. Quality German engineering - there's an oxymoron.
Enrique
Reviewed in Mexico on December 28, 2018
Excelente producto
Dr. Gregg E. Townsley
Reviewed in the United States on May 15, 2017
Outstanding addition to what is already an outstanding saw (my Bosch 4100). Outfeed Support Assembly arrived as promised. Additional parts are enclosed to make sure the assembly fits your saw. I was able to assemble and mount the kit in a little less than an hour. Assembly hints: 1) as indicated, DO NOT tool tighten the mounting bolts until entire unit is mounted, 2) mount when your saw and saw stand is erect, enabling the saw to be moved to its side for easier access, 3) while maybe obvious to some, indents or scoring on the unit rods are for the friction washers (no instructions pointed that out, I got lucky).
Customer
Reviewed in the United States on July 14, 2016
This is a sturdy piece of gear made from heavy duty metal. It was easy to install on my Bosch, taking only a few minutes for it to be ready. The task of ripping a long board is now made much easier. In the past, I've used rollers on tripods and found adjusting them difficult. Worse yet, in the middle of a cut, if the board caught the roller the support would fall over. With this product, the only adjustment is to set the extension of the support and you're good to go. I'm really pleased with it.
Recommended Products
$64.99
$ 24 .99 $24.99