Shopping Cart

Your cart is empty.

Your cart is empty.

DLC32 V2.1 32 Bit ESP32 GRBL TFT Engraver DIY Universal Main Board 32-bit Processor Module TMC2209 Stepper Motor App Control Work

4.6 (2) Write Review
Free shipping on orders over $29.99

$42.09

$ 19 .99 $19.99

In Stock
  • [APP CONTROL] - Achieve fast carving, webpage control, and mobile app control. Compatible with MKS DLC and other PC software.
  • [BASIC PARAMETERS] - 32 bit STM32 processor, expandable WIFI module, power outage relay module, material outage detection switch, and external card slot.
  • [FINE WORKMANSHIP] - Embedded with -core 32-bit high-speed MCU and powerful WIFI and modules. Equipped with 8MB flash storage chip for effective
  • [GOOD ACCURACY WORK] - Engraver touch screen for coordinated and accurate printing s.
  • [TMC2209 STEPPER MOTOR DRIVER] - Ultra quiet and designed to prevent overheating. for easy grip and control.


Product Description

1010230066111-1

DLC32 V2.1 32 Bit ESP32 GRBL TFT Engraver DIY Universal Main Board 32-bit Processor Module TMC2209 Stepper Motor App Control High Accuracy Work

YT


[FINE WORKMANSHIP] - Embedded with dual-core 32-bit high-speed MCU and powerful and modules. Equipped with 8MB flash storage chip for effective protection.


[BASIC PARAMETERS] - 32 bit STM32 processor, expandable module, power outage relay module, material outage detection switch, and external card slot.


[GOOD ACCURACY WORK] - Engraver touch screen for coordinated and accurate printing operations.

1

1010230066111-2

1010230066111-3

1

1010230066111-2

1010230066111-3


Specification:


Item Type: Engraver Mainboard


Main Board Parameters


Mode: MKSDLC32


Material: PCB


Voltage: 12-24V DC ( less than 10A)


Single Chip Computer: ESP32 WROOM 32U (32 bit)


MCU Frequency: 240MHz


Flash Memory: 8192KBytes


Memory: 520KBytes


Speed: Less than 8000mm/min


Offline Display: TS24 R, TS35 R


Firmware: GRBL


Serial Driver: USB


Axes Onboard: 4 (X, Y1, Y2, Z)


Website: Support


APP: Support


Storage Card: Supported


Tool: Support


Available Machines: CNC engraving machine


Stepper Driver: A4988, DRV8825, TMC2208, 2209, 2225 (Nema17 motor)


Additional Driver: TB6600, TMC2160 (applicable to Nema23 motor)


: Below 20W (greater than 20W, external power supply)


Compatible Software: For Grbl, for Xloader, for GrblController, for benbox, for mDraw, for LightBurn


Main Board Introduction: The DLC32 main board is an offline engraving control board developed specifically for desktop engraving machines. The hardware is equipped with a 32 bit high speed ESP32 module, integrated with function, and directly drives a 2.4, 3.5 inch touch color screen; It can achieve functions such as fast carving and webpage control, as well as mobile app control. The installation holes and circuit board size of DLC32 are compatible with for DLC and can also be used with for GRB and for LightBurn PC software.


TMC2209 Driver Parameters


Maximum Output Current: 2.5A


Default Current: 1.25A


Micro Step: Up to 1/256


Configuration: STEP DIR or UART


Load Driving Voltage Range: 5.5-28V


IC Logic Working Voltage: 3.3V 5V



How to Use:


Introduce usage based on the selling point diagram.



PackageList:


1 x Main Board


1 x USB Cable


3 x Driver


3 x Heat Sink



Amos
Reviewed in the United States on January 31, 2025
There needs to be clear instructions with this. It is not plug and Play.
Scott F.
Reviewed in the United States on April 19, 2024
Works very well.Be aware that this is loaded with non-specific grbl 1.1 My original unit was destroyed due to my error. I had not backed up my settings and spent significant time configuring this unit.I would purchase another if I were to build a custom machine.