Your cart is empty.
Your cart is empty.The Hakko T18-D08 0.8D Soldering Chisel Tip is used with Hakko's FX-888/FX-8801/907/900/913/928/936/937/703 Soldering Stations and Systems.
Maximzodal
Reviewed in the United States on June 6, 2024
I wish I had this when first starting my electronic hobby
Calvin W Lee
Reviewed in the United States on December 6, 2023
I needed this tip for use with SMT ICs doing a DIY buffer project. As described and does the job. Fast fulfillment.
Family Account
Reviewed in the United States on December 25, 2023
Long lasting tip, seems to be original Hakko.
Sebastien
Reviewed in France on December 23, 2023
Que dire de plus, on est sur du Hakko, la qualité des produits de cette marque n’est plus a démontrer.Ces pannes à souder sont d’une excellent qualité.
John Foster
Reviewed in the United States on August 29, 2022
worked great
Alex
Reviewed in Canada on February 18, 2020
So yeah, when first received it does not look like a chisel tip. I suspect this is due to a thin coating of solder. Once heated wiped, you will say "wow that's a small chisel". The cheap knockoffs do not even compare to original Hakko tips.
Grant M.
Reviewed in Canada on August 3, 2018
Excellent seller with the genuine part from Hakko.
onemanmechanic
Reviewed in Japan on January 12, 2017
同社FX-600を用いてsop-8等の小型ICに使用する為購入いたしました。根元からの体積がT18-C08より小さい為、標準のこて先同様の温度よりはかなり高めに設定しないと冷えやすいので、温度にシビアな部品は温度計必須と思われます。
S. CLOWN
Reviewed in the United States on June 1, 2014
Were any of you able to receive the correct tip? I purchased a station along with 5 tips. I had the same experience with the T18-D08.My tip is clearly marked T18-D08 but is see no chisel except for what might be a flat that does no extend to the end.There is a set of 5 tips offered on Amazon that has a very clear picture of the tips. You can clearly see the D08 marking on the tip but it looks wrong to me. The manufactures web page goes to great lengths to spell out the advantages of a chisel tip. I am retired after 40+ yearsof electronics and hold a micro soldering certification from the Navy. Good soldering is having the best and correct tip.After measuring a T18-D16 chisel tip I think I see whats going on. The T18-D08 manufactures spec is .8mm X .6mm. So after plating and tinning with solder presto its round for all practical purposes. I would guess it might last longer but you sure don't have the advantages of a squared off(in both planes)tip.:(
Paul Eastham
Reviewed in the United States on February 28, 2014
Computerthis is a soldering iron tip, it `fits is tight places, they come in many sizes, So they will handle components from smt to large components.It gets hot so do not touch the hot end.If you do not take care of it it will oxidize and burn out.Dear computer.every revue takes time, no matter what I say I can not help people buy a product like this.The soldering station and de soldering iron are excellent, BUY THEM.
amnjack
Reviewed in Japan on November 3, 2014
温調半田小手は，数10秒で温まるので重宝していますが，このドライバー型0.8mmは，あまり用途がありません。SOPでも使いづらく感じました。標準で温調半田小手に付いてくる円錐家と大差ありませんでした。
Nick G
Reviewed in the United States on January 11, 2014
This is a good tip to run on your Hakko FX-88x series soldering iron. I think it's at least worth mentioning to those who might not know, tips with a less sharp tip on it can be easier to work with when soldering. Other than that, this is a good purchase. I also recommend purchasing with this, some "tip tinner". If you keep your tip clean and well tinned, you won't be replacing it very often at all.
William Machrone
Reviewed in the United States on December 30, 2013
A screwdriver/chisel tip is just right for printed circuit work as well as general wiring, and 0.8mm is the right size. The photograph is wrong, however. It shows a conical tip.
Recommended Products
