Your cart is empty.
Your cart is empty. HzdaDeve Hardened Nozzles Stainless Steel Nozzles High Temperature Pointed Wear Resistant Nozzle 0.4MM 0.6MM 0.8MM Thread Print Head for R QIDI Q1 Pro/X-SMART3/X-PLUS3/X-MAX3 3D Printer (6 Pack)
Specification:
Material: Stainless Steel Hardend
Filament Diameter: 1.75mm
Nozzle Size: 0.4MM 0.2MM 0.6MM 0.8MM
Compatible Printer: for R QIDI Q1 Pro/X-SMART3/X-PLUS3/X-MAX3 D printer
Package Include:
2 Pack 0.4MM nozzles
2 Pack 0.6MM nozzles
2 Pack 0.8MM nozzles
After-Sale Service:
If there are any questions, just contact us freely, and a satisfactory solution will be provided within 24 hours
DC Nguyen
Reviewed in the United States on March 9, 2025
Direct swap. Ran calibration and first print was flawless!Thank You!
Gary F.
Reviewed in the United States on March 25, 2025
Sends the S1 into an error code!!
Denny Sawyer
Reviewed in the United States on February 12, 2025
These hot ends are by all appearances identical to the hotend that came on my S1. They fit perfectly, and work just as well as the original. Two things stop them from getting five stars - the first is that they cost a bit more than the Anycubic hotend costs (although you have to order directly from Anycubic right now, so it's not quite as convenient as getting it on Amazon). With the current 10% discount coupon, the price is reduced to just a few dollars more per hot end, so they're not a bad deal. The second is that they have a PTFE tube in the heat break instead of Anycubic's ceramic tube, which limits the temperature to under 270C. So if you need the original's 320C capability, these hot ends will not work for you.I don't find anything particularly wrong with the hot ends or the nozzles, other than some sloppiness in the application of the thermal grease. I had to wipe both nozzles clean with a towel before they could be used, but at least I know they used thermal grease in the assembly. Like any new hot end, I always assume they're not properly assembled at factory, so once installed on the printer, I heat the nozzle up to about 180C and tighten it with a nozzle wrench to prevent leaks. That technically shouldn't be necessary, but it's a good habit to get into, especially for these "volcano" style nozzles that just seat against the end of the heat break tube. Overall, a decent alternative to ordering parts directly from Anycubic, but they're not quite the equivalent of the original parts.
Stephen Fender
Reviewed in the United States on February 12, 2025
Perfect fit for the S1. Only took about 5 minutes to swap it out. Glad to have a backup.
Luis Aguirre
Reviewed in the United States on January 20, 2025
Was super easy to install the 0.6 nozzle on the Q1 Pro.So far its printing faster with no issues.
Michael Y.
Reviewed in the United States on September 17, 2024
I'm 80 hours into the .6 nozzle. Still maintaining a high print quality, while getting a little faster print times. No cloggs just good prints.Used on a Qidi Q1 pro.Only thing I've noticed is I've had to run my temps a little hotter with this nozzle.
Dan B.
Reviewed in the United States on September 12, 2024
These hardened nozzles are great for their long-life and wear resistance.I appreciate that the set comes with a variety of sizes for output, so you can pick from 0.4 all the way up to 0.8 MM.
wally3343
Reviewed in the United States on November 8, 2024
These are great nozzles and they held up well against several different kids of filament including carbon fiber. For the price you can’t go wrong.
Recommended Products
